Screen Adjustment - Kenwood DDX7032 Service Manual

5.7. DVD
• Use CD media KTD-02A, DVD media TDV-540A/TTD-100
to play back in the order of the following sequence.
• Use "Title1-Chapter1" while Loading.
• Check CDDA (KTD-02A)
• Use "Track UP/DW" to play back in the order of sequence
as shown below:
1 ↔ 9 ↔ 15 ↔ 10 ↔ 11 ↔ 12 ↔ 13 ↔ 14 ↔ 9 ↔ 1...
Track 28 is directly selected by pressing [RDM] key.
• DVD audio/video checking (TDV-540A)
Use "Chapter UP/DW" to play back in the order of se-
quence as shown in Tables 5.7.1 and 5.7.2.
Use FM/AM on the remote controller to change the video/
audio check.
For DVD video checking.
Title Chapter
3 6 Level
3 17 AM/PM noise
Frequency
3 8
characteristics
3 12 Color measurement
4 1 1kHz 0dB
4 6 17Hz
Table 5.7.1 DVD Video check
For DVD audio checking.
Title Chapter
4 1 1kHz 0dB
4 6 17Hz
4 16 44kHz
4 2 Infi nity
4 3 L
4 4 R
4 1 1kHz 0dB
4 2 Infi nity
Table 5.7.2 DVD Audio check
5.8. Audio
• The default setting of Volume shall be Step 30.
• In setting up BAL/FAD, the setting "MIN ↔ CENT ↔ MAX"
can be made by 1 click.
• In setting up Xover, the setting "MIN ↔ MAX" can be
made by 1 click.
• In setting up Tone, the setting "MIN ↔ CENT ↔ MAX" can
be made by 1 click.
• The default setting of Tone (EQ) shall be Flat.
• The default setting of System Q shall be Off.
TEST MODE
Audiostream
Audiostream1
Audiostream1
Audiostream1
Audiostream1
PCM96k/24bit Audiostream3
PCM96k/24bit Audiostream3
Audiostream
PCM96k/24bit Audiostream3
PCM96k/24bit Audiostream3
PCM96k/24bit Audiostream3
PCM96k/24bit Audiostream3
PCM96k/24bit Audiostream3
PCM96k/24bit Audiostream3
Dolby Audiostream1
Dolby Audiostream1
DDX7032/7032M/712
DNX7120/7220/7320
• When there is Digital Out terminal, the setting shall be
such that the output is always On.
• The default setting of Line Mute shall be On.
5.9. AV-IF
• The default setting of AV-IN Interruption shall be On.
• The default setting of R-CAM Interruption shall be On.
• Normally an interruption occurs when the R-CAM is de-
tected.
• Reverse condition shall be always On.
• The default setting of SP for NAVI interruption shall be
Front ALL.
• Use Tenkey 3 on the remote controller to change V-IN mir-
ror mode.

5.10. Screen adjustment

• By pressing Tenkey 5 on the remote control on each video
screen, each video screen's Screen adjustment items are
displayed.
• The default value is Center.1Items can move between "Full
Down ↔ Center ↔ Full Up" by 1 click.
• The default value of Bright during illumination Off shall be
MAX. (The Bright shall be Center during illumination On.)
5.11. BEEP
• Beep regardless of any destination.
But do not output the BEEP during the screen transfer
and iPod/USB operation. (While in Standby source, BEEP
cannot be output because of PWIC restriction.)
5.12. DC Offset
• DC Offset detection status (normal/error) clear
By pressing the [DC Offset Clear] key in the Service
screen, clear DC Offset detection information.
• DC Offset detection information is displayed on the Infor-
mation screen/Service screen.
• In the Test mode, even if DC Offset is detected, it is not
written into the nonvolatile memory.
However, the detection operation shall be carried out and
when the DC Offset is detected, the Protect shall be dis-
played and it becomes all CH Mute operation.
• Volume setting can be changed to the following settings
by pressing Tenkey 2 on the remote controller.
Source : DVD
Assigned DISC : KTD-02A
Assigned Track : 15 (20Hz, 0dB)
Assigned VOL : 26 Step
31