Table of Contents
Advertisement
Dimensions
Connecting Pin Assignments
Glossary
(RS-232C) Specifications and Command Settings
Aspect ratio
INPUT 2 COMPONENT/RGB Port: 15-pin Mini D-sub female connector
CONTROL CONTENTS
Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4 : 3. There are also wide images with an aspect ratio of 16 : 9
POWER ON
and 21 : 9.
5
POWER OFF
Auto Sync
Optimises projected computer images by automatically adjusting certain characteristics.
INPUT 1 (COMPONENT 1)
Background
INPUT 2 (COMPONENT 2)
Initial setting image projected when no signal is being input.
INPUT 3 (S-VIDEO)
Clock
Clock adjustment is used to adjust vertical noise when clock level is incorrect.
INPUT 4 (VIDEO)
CLR Temp (Colour temperature)
Function that can be used to adjust the colour temperature to suit the type of image input to the projector. Decrease the colour temperature to create warmer,
reddish images for natural flesh tones, or increase to create cooler, bluish images for a brighter picture.
10
Composite sync
• If an underbar (_) appears in the parameter column, enter a space.
15 14 13 12 11
Signal combining horizontal and vertical sync pulses.
Digital keystone correction
Side View
Function to digitally correct a distorted image when the projector is set up at an angle, smoothes out jaggies on keystone images and compresses the image
not only horizontally but vertically keeping the 4 : 3 aspect ratio.
Digital shift
Shifts image up or down easily by
inputs.
GAMMA
Image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter
portions. You can select from four different modes: Standard, Black Detail, White Detail and Brighten.
Intelligent compression and expansion
High quality resizing of lower and higher resolution images to fit the projector's native resolution.
Phase
Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontal
flicker.
RESIZE
RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable
Allows you to modify or customize the picture display mode to enhance the input image. You can select from four different modes: NORMAL, FULL, BORDER
and STRETCH.
RS-232C
1 2 3 4 5
Function to control the projector from the computer by using the RS-232C ports on the projector and computer.
Stretch
Mode that stretches the 4:3 image horizontally to display it on the wide screen.
Sync on green
Video signal mode of a computer which overlaps horizontal and vertical sync signal to green colour signal pin.
6 7 8 9
Front View
Bottom View
Downloaded From projector-manual.com Sharp Manuals
Downloaded From projector-manual.com Sharp Manuals
Downloaded From projector-manual.com Sharp Manuals
Downloaded From projector-manual.com Sharp Manuals
-51
-53
-55
-57
COMMAND PARAMETER
P
O
W
R
_
_
_
1
OK OR ERR
4
3
2
1
P
O
W
R
_
_
_
0
OK OR ERR
I
V
E
D
_
_
_
1
OK OR ERR
I
V
E
D
_
_
_
2
OK OR ERR
I
V
E
D
_
_
_
3
OK OR ERR
I
V
E
D
_
_
_
4
OK OR ERR
9
8
7
6
/
buttons when RESIZE mode of input image is NORMAL, BORDER, or STRETCH of COMPUTER, VIDEO and DTV
Pin No.
Signal
1
2
RD
3
SD
4
5
SG
6
7
8
9
RETURN
Rear View
RGB Input
Pin No. Signal
1
Video input (red)
2
Video input
(green/sync on green)
3
Video input (blue)
4
Not connected
5
Composite sync
6
Ground (red)
7
Ground (green/sync on green)
Top View
Component Input
Pin No. Signal
1
Video input P
(C
R
R
2
Video input Y
3
Video input P
(C
B
B
4
Not connected
5
Not connected
6
Ground (P
)
R
7
Ground (Y)
Name
Receive Data
Send Data
Reserved
Signal Ground
Reserved
Reserved
Reserved
368
Pin No. Signal
8
Ground (blue)
9
Not connected
10
Ground
11
Ground
12
Bi-directional data
13
Horizontal sync signal
14
Vertical sync signal
15
Data clock
Side View
Pin No. Signal
)
8
Ground (P
9
Not connected
)
10
Not connected
11
Not connected
12
Not connected
13
Not connected
14
Not connected
15
Not connected
I/O
Reference
Not connected
Input
Connected to internal circuit
Output
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
)
B
Units: mm
Advertisement
Table of Contents
