Kenwood DDX6034 Service Manual page 18

DDX6034/6034M/6054/7034BT/7034BTM/714
DNX7000EX/7140/7240BT/7340BT
2.3.6. DVS-8000 Adjustment screen
This is to display DVS-8000 Servo Adjustment screen. (As
for the details of the adjustment procedures, refer to the
mechanism specifi cations.)
The DVS8000 Adjustment screen is displayed in Figure 2.3.6.
DVS8000 Adjust
Offset Cancel Inner Limit
Focus Height
Cancel
Figure 2.3.6 DVS-8000 Adjustment screen
Key Specifi cation
Offset Cancel : Start the Offset Cancel Adjustment.
Inner Limit : Start the Inner Limit Adjustment.
Focus Height : Start the Focus Height Adjustment.
Cancel : Transfer to Service screen.
Return : Transfer to the DVS8000 Adjustment
screen. (left screen in Figure 2.3.6)
* Select black for the background color until "Adjust OK/
NG" is displayed.
Modify the background color to blue at the same time as
"Adjust NG" is displayed.
Modify the background color to red at the same time as
"Adjust NG" is displayed.
2.3.7. Direct Select screen
Pressing the [Direct Select] key on the Test Mode Main
screen can transfer to the GUI screen in normal operation.
At this time, transfer to the Source Select screen.
2.3.8. Touch Adjust screen
Fine-tune the variations of touch feeling in of each set.
Touch 4 markers one by one, and the adjustment is com-
pleted when the "Write OK" is shown on the screen.
If the "Write NG" is shown, transfer to the Test mode again
to re-start the adjustment from the fi rst step.
The Touch Adjustment screen is shown in Figure 2.3.8.
Touch Adjust
1-point 2-point
Cancel
being input being input
3-point being input 4-point being input
Figure 2.3.8 Touch Adjust screen
18
TEST MODE
DVS8000 Adjust
Adjust OK/NG
Return
Touch Adjust
Write OK/NG
Return
Key Specifi cation
Cancel : When the Cancel button is pressed while enter-
ing the 1st point, the system transfers to the
Test Mode Main screen.
When the Cancel button is pressed while en-
tering the other point than the 2nd point, the
system transfers to the status to enter the 1st
point.
Return : Transfer to Test Mode Main screen.
* Select black for the background color until "Write OK/NG"
is displayed.
Modify the background color to blue at the same time as
"Write OK" is displayed.
Modify the background color to red at the same time as
"Write NG" is displayed.
2.3.9. Illumi Adjustment screen
Perform adjustment of white color used for the Key Illumi.
The Illumi Adjustment screen is displayed in Figure 2.3.9.
When checking the Key Top,
enlarge the screen.
Illumination Adjust
Table9 Table3 Table5 Table7
Table10 Table10 Table4 Table6
Table8 Table4 Table6 Table8
Table2 Table2 Table2
Cancel Table1 Next
Illumination Adjust
Write OK/NG
Return
Figure 2.3.9 Illumi Adjustment screen
Key Specifi cation
Next : Transfer to the next Adjustment screen.
Cancel : Transfer to the previous Adjustment screen.
(Transfer to the Test Mode Main screen dur-
ing the screen in the leftmost part of Figure
2.3.9 is being displayed.)
Table1~10 : Select a Table for the Key Illumi.
Red : Turn the Red Offset mode ON.
Green : Turn the Green Offset mode ON.
Blue : Turn the Blue Offset mode ON.
Yellow : Turn the Yellow Offset mode ON.
Up/Down (Red)
: Red Offset key. (This key is displayed only
when the Red Offset mode is turned ON)
Illumination Adjust
Red Step value DW UP
Green Step value DW UP
Blue Step value DW UP
Yellow Step value DW UP
Cancel RGB offset value Next
Illumination Adjust
Adjustment value
Direct adjustment bar
DW UP
Next
Cancel