Toro 03673 Reelmaster 5410-G Operator's Manual page 20

Engine Run
Backlap
Settings
Menu Item
Units
Language
LCD Backlight
LCD Contrast
Front Backlap Reel Speed
Rear Backlap Reel Speed
Protected Menus
Auto Idle
Blade Count
Mow Speed
Height of cut (HOC)
F Reel RPM
R Reel RPM
* Only "operator-faced" text is translated. Faults, Service, and
Diagnostics screens are "service-faced". Titles will be in the
selected language, but menu items are in English.
About
Menu Item
Model
SN
Indicates the inputs, qualifiers
and outputs for starting the
engine.
Indicates the inputs, qualifiers
and outputs for operating the
backlap function.
Description
Controls the units used on the
InfoCenter. The menu choices
are English or Metric
Controls the language used
on the InfoCenter*.
Controls the brightness of the
LCD display.
Controls the contrast of the
LCD display.
Controls the speed of the front
reels in backlap mode.
Controls the speed of the rear
reels in backlap mode.
Allows the
superintendant/mechanic
to access protected menus by
inputting a passcode.
Controls the amount of time
allowed before returning the
engine to low idle when the
machine is stationary.
Controls the number of blades
on the reel for reel speed.
Controls the ground speed for
determining the reel speed.
Controls the height of cut
(HOC) for determining the reel
speed.
Displays the calculated reel
speed for the front reels. The
reels can also be manually
adjusted.
Displays the calculated reel
speed for the rear reels. The
reels can also be manually
adjusted.
Description
Lists the model number of the
machine.
Lists the serial number of the
machine.
Machine Controller Revision
InfoCenter Revision
CAN Bus
Protected Menus
There are 7 operating configuration settings that are adjustable
within the Settings Menu of the InfoCenter: auto idle time
delay, Blade Count, Mow Speed, Height of Cut (HOC), F
Reel RPM and R Reel RPM. These settings can be locked
by using the Protected Menu.
Note: At the time of delivery, the initial password code is
programmed by your distributor.
Accessing the Protected Menu Settings
To access the Protected Menu Settings
•
From the Main Menu, scroll down to the Settings Menu
and press the right button.
•
In the Settings Menu, scroll down to the Protected Menu
and press the right button.
•
To enter the passcode, use the center button to set the
first digit then press the right button to move on to the
next digit.
•
Use the center button to set the second digit then press
the right button to move on to the next digit.
•
Use the center button to set the third digit then press the
right button to move on to the next digit.
•
Use the center button to set the fourth digit then press
the right button.
•
Press the middle button to enter the code.
•
If the code has been accepted and the protected menu has
been "Unlocked", "PIN" will be displayed in the upper
right corner of the display screen.
The ability to view and change the settings in the Protected
Menu can be changed. Once the Protected Menu has been
accessed, scroll down to Protect Settings. Using the right
button, changing Protect Settings to OFF will allow the
ability to view and change the settings in the Protected Menu
without entering the passcode. Changing Protect Settings to
ON will hide the protected options and will require entering a
passcode to change the setting in the Protected Menu. After
the pass code has been set, the key switch must be turned off
and back on to enable and save this feature.
Note: If the passcode has been forgotten or misplaced,
please contact your distributor for assistance.
To Set the Auto Idle
•
In the Settings Menu, scroll down to Auto Idle.
•
Press the right button to change the auto idle time
between OFF, 8S, 10S, 15S, 20S, & 30S.
20
Lists the software revision of
the master controller.
Lists the software revision of
the InfoCenter.
Lists the machine
communication bus status.