Using The Non-Stop Relay Function; Auto Change Function; Software Update - Samsung MX-J630 User Manual

Using the NON-STOP RELAY Function

The NON-STOP RELAY function plays music con-
tinuously without an interval between tracks/files.
For example, for two successive music files, the
function skips to a position 10 seconds after the
start of the second file when there are 10 seconds
of playing time left in the first file.
1. Press the NON-STOP RELAY button on the
remote control.
Each time you press this button, the mode
changes as follows:
ON-NON-STOP MUSIC RELAY ; OFF-NON-STOP
MUSIC RELAY
2. To cancel this function, press the NON-STOP
RELAY button until "OFF-NON-STOP MUSIC
RELAY" is displayed.
• This function is only available during
playback of a CD/USB.

Auto Change Function

You can play a disc followed by a USB continuously.
1. Press the AUTO CHANGE button, and then
use buttons or
, , .
a setting, and then press
selection.
• If My List Play has not been set in CD/USB mode,
the settings change as follows:
AUTO CHANGE OFF ; ALL
• If My List Play has been set in CD/USB mode, the
settings change differently:
AUTO CHANGE OFF; ALL ; MYLIST
• When the AUTO CHANGE mode is "ALL", the Hi-Fi
Component will play music from DISC, USB1, and USB2
continuously.
• When the AUTO CHANGE mode is "MYLIST", the Hi-
Fi Component will play My List tracks from DISC, USB1,
and USB2 continuously.
• When the auto change mode is "ALL/MYLIST", if
you press the POWER button, FUNCTION button, or
the OPEN/CLOSE button, the auto change function
automatically switches to "OFF" mode.
• When the USB is playing, if you disconnected the USB,
the auto change function automatically switches to
"OFF" mode.
• When the auto change mode is "ALL/MYLIST", the unit
cannot record.
• When the auto change mode is "ALL/MYLIST", the
REPEAT function automatically change to OFF.
• When the auto change mode is "ALL/MYLIST", the
DELETE, USB REC, MY LIST and REPEAT functions do
not work, and the unit displays " ALL/MYLIST-AUTO
CHANGE ".
• When DISC play ends, if there's no USB 1, the unit will
play music from USB 2.
• When DISC play ends, if there's no USB 1 and USB 2, the
unit will continue to play the disc.
• When USB 2 play ends, if there's no DISC, the unit will
play music from USB 1.
buttons to select
[, ]
to apply your

Software Update

Samsung may offer updates for the product's sys-
tem firmware in the future.
If an update is offered, you can update the firm-
ware by connecting a USB device with the firm-
ware update stored on it to the USB port on your
product.
Note that if there are multiple update files, you
must load them onto the USB device singly and
use them to update the firmware one file at a
time.
Please visit samsung.com or contact the Samsung
Call Center to receive more information about
downloading updates files.
• Select USB function, insert a USB device containing
the firmware update into the USB port on the main
unit.
• Updating firmware may not work properly if audio
files supported by the product are stored in the USB
storage device.
• Do not disconnect the power or remove the USB
device while updates are being applied. The main
unit will turn off automatically after completing the
firmware update.
• After the update, all settings are reset to their
factory default settings. We recommend you write
down your settings so that you can easily reset
them after the update.
If the firmware fails to update, we recommend
formatting the USB device in FAT16/FAT32 and
trying again.
• Once the software update is completed, turn on
the product with no disc inserted. The "NO DISC"
message appears on the display. Press and hold the
STOP button on the main unit for longer than 5
seconds. "INIT " appears on the display and the unit
powers off. The upgrade is complete.
• Do not format the USB device in the NTFS format.
The product does not support the NTFS file system.
• Depending on the manufacturer, some USB devices
may not be supported.
• The product has a DUAL BOOT function. If the
firmware fails to update, most functions will
become inoperable and "UPGRADE FIRMWARE"
will appear on the display. Update the firmware
again.
19 18
English English