Check Points Before Operation; Auto Calibration; Starting Osd Menu; Reserved Preset - Samsung SCC-C6323P User Manual

CHECK POINTS BEFORE OPERATION

• Before power is applied, please check the cables carefully.
• The camera ID of the controller must be identical to that
of the camera to be controlled. The camera ID can be
checked in the System Information of OSD Menu.
• If your controller supports multi-protocols, the protocol
must be changed to match to that of the camera.
• If you changed camera protocol by changing DIP switch,
the change will be effective after you reboot the camera.
• Since the operation method can be different for
each controller available, refer to the manual for your
controller if camera can not be controlled properly.
PRESET AND PATTERN
FUNCTION PRE-CHECK
• Check how to operate Preset, Scan, Auto Pan and
Pattern function with controller or DVR in advance to
operate camera function using them. (refer to your
System keyboard Manual)
• If controller or DVR has no pattern button or function,
use shortcut keys with preset numbers. For more
information, refer to "Reserved Preset" in this manual.

AUTO CALIBRATION

• If the camera is continuously subjected to very high
temperature (over 50°C or 122°F) environment for a
long time, it is possible for the camera to lose focus.
As a result, you will get blurry image. In this case, it is
recommended to turn on "AUTO CALIBRATION" by
running Preset 165.
• If you execute AUTO CALIBRATION, camera will
calibrate its focus at every 6 hours. To turn off this
function, please, Run Preset 166.

STARTING OSD MENU

• Function
Using the OSD menu, Preset, Pattern, Auto Pan,
Scan and Alarm Input function can be confi gured for
each application.
• Enter Menu
<Go Preset> [95]

RESERVED PRESET

• Description
Some Preset numbers are reserved for direct access
to specifi c functions in OSD menu. These direct
commands via preset provide quick execution of
Operation
various functions using keyboard controller as well as
simplify the interface with DVR and IP equipments.
• Function
<Go Preset> [95]
<Go Preset> [131~134]
<Go Preset> [141~148]
<Go Preset> [151~158]
<Go Preset> [161]
<Set Preset> [161]
<Go Preset> [165]
<Go Preset> [166]
<Go Preset> [167]
<Set Preset>[167]
<Go Preset> [170]
<Go Preset> [171]
<Go Preset> [174]
<Go Preset> [175]
<Go Preset> [176]
<Go Preset> [177]
<Go Preset> [178]
<Go Preset> [179]
<Go Preset> [190]
<Go Preset> [191]
<Go Preset> [192]
<Go Preset> [193]
<Go Preset> [194]
<Go Preset> [195]
<Go Preset> [196]
<Go Preset> [197]
<Go Preset> [198]
<Go Preset>[200]
<Go Preset>[201]
: Enters into OSD menu
: Runs Pattern Function 1 ~ 4
: Runs Auto Pan Function 1 ~ 8
: Runs Scan Function 1 ~ 8
: Sets Relay Output to OFF
: Sets Relay Output to ON
: Auto Calibration ON
: Auto Calibration OFF
: Zoom Proportional Jog ON
: Zoom Proportional Jog OFF
: Sets Camera BLC Mode to OFF
: Sets Camera BLC Mode to HIGH
: Sets Camera Focus Mode to
AUTO
: Sets Camera Focus Mode to
Manual
: Sets Camera Focus Mode to
SEMI-AUTO
: Sets Day & Night Mode to
AUTO1
: Sets Day & Night Mode to
NIGHT
: Sets Day & Night Mode to DAY
: Sets OSD Display Mode to
AUTO (Except Privacy Mask)
: Sets OSD Display Mode to OFF
(Except Privacy Mask)
: Setting OSD Display Mode to
ON (Except Privacy Mask)
: Sets all Privacy Mask Display to
OFF
: Sets all Privacy Mask Display to
ON
: Heater ON (Turn off after 5mins
and switch to Auto mode)
: Heater OFF (Turn off and switch
to Manual mode)
: Fan ON (Turn off after 5mins
and switch to Auto mode)
: Fan OFF (Turn off and switch to
Manual mode)
: Digital Zoom ON
: Digital Zoom OFF
English – 21