Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Shibaura Manuals
  4. Lawn Mower
  5. CM214
  6. Operator's manual

Shibaura CM-214 Operator's Manual

Hide thumbs Also See for CM-214:

Advertisement

Quick Links

See also: Workshop Manual
Enlarged version
CONTENTS
SAFETY .......................................................................................0-2
SECTION1 - GENERAL INFORMATION .............................................1-1
SECTION2 - OPERATION ...............................................................2-1
SECTION3 - LUBRICATION AND MAINTENANCE ..............................3-1
SECTION4 - SPECIFICATIONS.........................................................4-1
PREDELIVERY SERVICE ...............................................................4-5

TO THE OWNER:

This manual contains information concerning the operation, adjust, and maintenance of the CM
Mower. You have purchased a dependable machine, but only by proper care and operation can you
expect to receive the performance and long service built into this Mower. Please have all operators
read this manual carefully and keep the manual available for ready reference.
Your SHIBAURA dealer will instruct you in the general operation of you Mower. (Refer to the
"Delivery Report" at the back of this manual.) Your dealer's staff of factory-trained service technicians
will be glad to answer any questions that may arise regarding the operation of your Mower.
Your SHIBAURA dealer carries a complete line of genuine SHIBAURA parts. These parts are
manufactured and carefully inspected to insure high quality and accurate fitting of any necessary
replacement parts.
CAUTION: THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER PERSONAL
SAFETY IS INVOLVED. TAKE TIME TO READ AND FOLLOW THE INSTRUCTIONS. BE
CAREFUL!
CAUTION: PICTURES IN THIS MANUAL MAY SHOW PROTECTIVE SHIELDING OPEN OR
REMOVED TO BETTER ILLUSTRATE A PARTICULAR FEATURE OR ADJUSTMENT.
BE CERTAIN, HOWEVER, TO CLOSE OR REPLACE ALL SHIELDING BEFORE OPERATING
THE MACHINE.
IMPROVEMENTS
ISHIKAWAJIMA-SHIBAURA is continually striving to improve its products. We reserve the right to
make improvements or changes when it becomes practical and possible to do so, without incurring
any obligation to make changes or additions to the equipment sold previously.
0-1

Advertisement

loading

Related Manuals for Shibaura CM-214

Summary of Contents for Shibaura CM-214

  • Page 1: Table Of Contents

    Your SHIBAURA dealer will instruct you in the general operation of you Mower. (Refer to the "Delivery Report" at the back of this manual.) Your dealer's staff of factory-trained service technicians will be glad to answer any questions that may arise regarding the operation of your Mower.

  • Page 2: Safety

    SHIBAURA Dealer. If, however, service operations are to be undertaken on parts that Do not permit anyone but the operator to ride on the contain asbestos, the essential precautions listed unit.
  • Page 3 22. Disengage power to mower deck before backing up. Do not bypass the neutral safety start switch. Do not mow in reverse unless absolutely necessary Consult your SHIBAURA Dealer if your neutral safety and then only after careful observation of the entire start controls malfunction.
  • Page 4 SAFETY PRECAUTIONS SAFETY PRECAUTIONS Safety is NO accident.........Be Alert! Periodically maintain mower. Tighten nuts, bolts and • fittings periodically and lubricate mower for proper and This symbol is used to attract your attention safe operation. Check blades for tightness. to the safety precautions that should be understood by the operator to avoid accidents.
  • Page 5 DECALS SAFETY DECALS If safety or instruction decals become damaged or illegible, new decals should be obtained from your SHIBAURA Dealer and placed at their original positions. SAFETY DECALS WARNING: MUFFLER PART NO: 490992440 • Stay clear of hot surface.
  • Page 6 INSTRUCTION DECALS INSTRUCTION DECALS DIESEL FUEL PART NO: 490992430 STARTER SWITCH PART NO: 390197720 LIFT CONTROL LEVER PART NO: 390372400 PARKING BRAKE PART NO: 390197710 ENGINE OIL PART NO: 390230120 GUARANTEED SOUND POWER LEVEL MARK Guaranteed Sound Power Level According to Directive 2000/14/EC PTO CONTROL LEVER PART NO: 390173600...

  • Page 7: Section1 - General Information

    For your convenience, have your dealer record these numbers in the appropriate spaces below. ISHIKAWAJIMA-SHIBAURA MACHINERY CO., LTD. is continually striving to improve its products. We reserve the right to change prices, specification, or equipment at any time without notice.
  • Page 8 GENERAL INFORMATION GENERAL INFORMATION MINIMUM HARDWARE TIGHTENING TORQUES MINIMUM HARDWARE TIGHTENING TORQUES IN FOOT POUNDS (NEWTON-METERS) FOR NORMAL ASSEMBLY APPLICATIONS IN FOOT POUNDS (NEWTON-METERS) FOR NORMAL ASSEMBLY APPLICATIONS INCH HARDWARE AND LOCKNUTS METRIC HARDWARE AND LOCKNUTS SAE GRADE 2 SAE GRADE 5 SAE GRADE 8 LOCKNUT CLASS 5.8...

  • Page 9: Section2 - Operation

    GENERAL INFORMATION INTERNATIONAL SYMBOLS SECTION 2 As a guide to the operation of your tractor, various international symbols have been used on instruments OPERATION and controls. These symbols are depicted and described below. CONTROLS AND INSTRUMENTS Hours Recorded Neutral SEAT, SEAT BELT AND ROPS If the seat belt is to be cleaned, use soap and Battery water.
  • Page 10 OPERATION OPERATION INSTRUMENT PANEL SWITCHES For safe operation, always check to make certain the lift control lever is in neutral before KEY START SWITCH attempting to start engine. Refer to page 2-7 for complete starting instructions. IMPORTANT: The key start switch must remain in the "ON' position while operating the engine.
  • Page 11 OPERATION OPERATION BRAKE CONTROL To apply the parking brake: Automatic Four-Wheel Drive (FWD) means that To stop the unit, release the pedal gradually the four-wheel drive line is engaged (except on an emergency). When release, the Depress the brake pedal to stop the unit. •...
  • Page 12 OPERATION OPERATION OPERATING THE HYDRAULIC LIFT SYSTEM BREAK-IN PROCEDURES STARTING THE ENGINE WARM WEATHER STARTING The hydraulic lift system provides accurate, Your CM Mower will provide long and SAFETY STARTING DEVICE To start a cold engine in warm weather or to smooth, and instant hydraulic power for raising dependable service if given proper care during start an engine that is warm;...
  • Page 13 OPERATION OPERATION COLD WEATHER STARTING 2. Connect one end of the jumper cable to the ENGINE WARM-UP OPERATION SHUT-OFF DEVICE battery positive (+) terminal and the other to If the engine fails to start using the preceding the auxiliary battery positive (+) terminal. In cold weather, run the engine at half throttle for The CM Mower is equipped with operation warm weather starting procedure or when...

  • Page 14: Section3 - Lubrication And Maintenance

    OPERATION SECTION 3 OVER HEATED ENGINE DRIVING THE CM MOWER The coolant temperature fluctuates depending LUBRICATION AND MAINTENANCE on ambient temperatures and working loads. If the needle at the "H" end indicates during operation, the overheat alarm buzzer sounds. This section gives full details of the service procedures necessary to maintain your CM Mower at This time take the following steps.
  • Page 15 LUBRICATION AND MAINTENANCE LUBRICATION AND MAINTENANCE LUBRICATION AND MAINTENANCE CHART LUBRICATION To lubricate these points: Adequate lubrication and maintenance on a 1. Wipe away all old grease and dirt from the regular schedule is vital to maintaining your lubrication fittings to prevent dirt or foreign CM mower.
  • Page 16 This opening is used to apply the grease to • If the original fuel tank cap is lost, always transmission INPUT shaft, to check or replace replace it with a SHIBAURA approved cap. the PTO belts. A "will-fit" cap may not be safe.
  • Page 17 LUBRICATION AND MAINTENANCE LUBRICATION AND MAINTENANCE FUEL AND LUBRICANT SERVICE PROCEDURES 2. Next, place a container below the oil filter A to catch the used oil and unscrew the oil filter. Discard the used oil and filter. ENGINE 3. Coat the gasket on the new filter with a film Checking the Engine Oil Level of clean oil.
  • Page 18 LUBRICATION AND MAINTENANCE LUBRICATION AND MAINTENANCE BLEEDING THE FUEL SYSTEM AIR CLEANER 2. Clean the primary element using low air IMPORTANT: Never tap the element with pressure (30 PSI or less). Blow dust from the hard objects or against a hard surface. This The CM Mower fuel system is designed to bleed The air cleaner is accessed by opening the inside to the outside of the element (opposite...
  • Page 19 LUBRICATION AND MAINTENANCE LUBRICATION AND MAINTENANCE TRANSMISSION, FRONT AXLE AND HYDRAULIC OIL FILTER (SUCTION & HST) HYDRAULIC SYSTEM The hydraulic system is equipped with spin-on Checking Oil Level: Check the oil level every type oil filters. 50 hours. NOTE: Replace the filters after the first 50 1.
  • Page 20 LUBRICATION AND MAINTENANCE LUBRICATION AND MAINTENANCE REAR AXLE DIFFERENTIAL CASE AND GENERAL MAINTENANCE FINAL REDUCTION GEAR CASES COOLING SYSTEM Checking Oil Level: Check the oil level every 100 hours. The CM mower engine must operate at the 1. With the engine off and the tractor standing correct temperature to obtain maximum level, check the oil level using the combined efficiency and service life.
  • Page 21 LUBRICATION AND MAINTENANCE LUBRICATION AND MAINTENANCE Draining and Flushing the Cooling System Fan Belt NOTE: Drain and flush the radiator and NOTE: Check the condition of the fan belt engine block every 12 months. Refill with a after every 50 hours of operation. Check fan 50/50 mixture of permanent antifreeze and belt tension after every 200 hours of clear water.
  • Page 22 However, make sure the solution does not get 3. Install the vent plug after making sure the disconnect the negative (-) cable first. SHIBAURA Dealer. inside the battery. After cleaning, wash the vent holes are not blocked. At below freezing...
  • Page 23 LUBRICATION AND MAINTENANCE LUBRICATION AND MAINTENANCE FUSE BLOCK To replace the fusible link wire: PTO BELT The fuse block is located on the left side of the 1. Disconnect the negative battery cable from Front-PTO and Side-PTO shafts are driven by mower compartment.
  • Page 24 LUBRICATION AND MAINTENANCE LUBRICATION AND MAINTENANCE Adjust the PTO belt tension as follows. SIDE-PTO Belt Tension TIRES • Use a clip-on tire chuck with a remote hose and gauge. This allows the operator to stand Front-PTO Belt Tension. 1. Remove the under-seat cover. NOTE: Check tire pressure after every 50 clear of the tire while inflating.

  • Page 25: Section4 - Specifications

    LUBRICATION AND MAINTENANCE SECTION 4 STORING THE MOWER UNIT A CM Mower that is to be stored for an SPECIFICATIONS extended period should be protected during storage. The following is a suggested list of operations to be carried out. 1. Thoroughly clean the unit. Use touch-up ENGINE paint where necessary to prevent rust.

  • Page 26: Predelivery Service

    SPECIFICATIONS CAPACITY Fuel Tank 28.0Î PRE-DELIVERY SERVICE Engine Oil 3.5Î CHECK AND ADJUST AS REQUIRED Coolant 3.5Î INOPERATIVE SERVICE CHECKS SAFETY ITEMS CHECKS OPERATIVE SERVICE CHECKS Transmission Oil 14.0Î 1. Tire pressure □ 1. Safety decals installed □ ・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・ All operating checks are to be performed with the Front 2.
  • Page 27 PRE-DELIVERY SERVICE CHECK AND ADJUST AS REQUIRED INOPERATIVE SERVICE CHECKS SAFETY ITEMS CHECKS OPERATIVE SERVICE CHECKS □ □ 1. Tire pressure 1. Safety decals installed All operating checks are to be performed with the Front ・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・ 2. Air cleaner element and hose 2.
  • Page 28 I, the undersigned, certify that, the products deseribed below conform to the specifications of Directive 98/37/EC Harmonized Standard : EN836 Products : 1. Category : Professional Mower 2. Make : SHIBAURA 3. Model : CM214 Tokyo, Oct. 11, 2001 Yoshimasa Kitou General Manager Tractor Division Ishikawajima-Shibaure Machinery Co., Ltd.
  • Page 29 FM48 3154 Tokyo, January 1, 2002 Yoshimasa Kitou General Manager Tractor Division Ishikawajima-Shibaura Machinery Co., Ltd. 5-32-7, Sendagaya, Shibuya-ku, Tokyo, JAPAN Name and address of the Notified Body : TÜV Süddeutschland Group, TÜV Bau und Betrieb GmbH Westendstrasse 199 D-80339 Munich Germany Déclaration de Conformité...