Rec Function - Panasonic AJ-SPX800P Operating Instructions Manual

8-2-4 REC FUNCTION

Items/ Adjustable
Data Saved Range
INTERVAL REC ON
MODE ONE SHOT
OFF
– – – F –
REC TIME 00s01f
:
59s29f
– C U F –
PAUSE TIME 00h00m00s01f
:
00h04m59s29f
:
23h59m59s29f
– C U F –
TAKE TOTAL NONE
TIME :
5day
– C U F –
TOTAL REC 00m00s01f
TIME :
99m59s29f
OVER100min
NONE
– – – – –
AUDIO REC ON
OFF
– C U F –
START DELAY 0SEC
:
10SEC
– C U F –
PRE REC TIME 0SEC
:
15SEC
– C U F –
LOOP REC ON
MODE OFF
– – – F –
Downloaded From VideoCamera-Manual.com Manuals
Remarks
Sets INTERVAL REC function.
ON: Uses internal memory to perform
interval recording.
ONE SHOT:
Performs "one-shot" recording for the
duration specified under REC TIME, and
then stops.
OFF: INTERVAL REC is not performed.
<Note>
After the power is turned off, this setting
defaults to OFF when the power is next
turned on.
Set REC TIME (1 cut).
<Note>
During 24P or 24PA modes, operations are
performed in 5-frame units, and the fraction
is truncated. The minimum operation is 5
frames (if the setting is 9 frames or fewer).
Specify PAUSE time for recording.
<Note>
During 24P or 24PA modes, operations are
performed in 5-frame units, and the fraction
is truncated. The minimum operation is 5
frames.
Specify the time needed for shooting.
Select from NONE (continue until operation
is manually stopped) to 5 days.
Display total recorded time. The setting
cannot be changed using this option.
Displays the recording time (recording time
needed for the P2 card) calculated using
REC TIME, PAUSE TIME, and TAKE TOTAL
TIME.
<Note>
During 24P mode or 24PA mode, operations
are performed in 5-frame units, and the
fraction is truncated. The displayed value is
based on actual operation using 5 frames as
a unit.
Select whether or not sound will be
recorded.
Set the delay after pressing REC START to
start recording in INTERVAL REC.
Set PRE RECORDING.
0-15SEC:
Set the length of time that can be
retrospectively recorded before the REC
START button is pressed.
<Note>
The maximum selectable range is 8 seconds
when the REC MODE in the <SYSTEM
MODE> screen is set to 50M (DVCPRO50).
Select whether or not to enable LOOP REC.
This setting can be used with PRE
RECORDING features.
ON: Enable LOOP REC.
OFF: Disable LOOP REC.
<Note>
After the power is turned off, this item will
default to OFF the next time the power is
turned on.
Items/ Adjustable
Data Saved Range
VOICE MEMO ON Set the available memory space for voice
memos in P2 cards.
RESERV OFF
ON: Reserve a voice memo area of 10
OFF: Do not reserve any voice memo
<Note>
Even when this item is set to OFF, and FULL
is displayed for the P2 card's recording
capacity, it may be possible to record voice
memos depending on the status of the P2
card.
– C U F –
REC START ALL Select operating modes that allow recording
NORMAL to start.
ALL: Allow recording to start during stop,
NORMAL:
Allow recording to start during stop and
recording pause.
<Note>
When the INTERVAL REC MODE is set to
either "ON" or "ONE SHOT", the "ALL"
setting for this option switches to "NORMAL"
– C U F –
operation.
P.ON REC HOLD Select the recording order of the slot when
the power is turned on.
SLOT SEL SLOT1
HOLD:
The recording order starts with the card
previously selected when the power was
turned off.
SLOT1:
The recording order starts with the card
that is inserted in Slot 1 when the power
– C U F –
is turned on.
<Note>
Displayed REC TIME, PAUSE TIME and TOTAL REC TIME are
translated into either drop-frame or non-drop-frame according to
the mode of operation.
TAKE TOTAL TIME is actual time. Therefore, TOTAL REC TIME
may incorporate fractions, depending on the settings.
Example of drop-frame
REC TIME
PAUSE TIME
TAKE TOTAL TIME
TOTAL REC TIME
The ____ in the Adjustable Range column indicates the preset
mode.
Remarks
minutes or longer separately from the
video recording capacity. The voice
memo area can be used even when
FULL is displayed for the recording
capacity of the P2 card.
space.
recording pause, and playback.
02s00f
02s00f
40min
19m59s06f
8
101