Roland R-8M Owner's Manual page 125

MIDI Implementation
Ottpn LSB
Siatus
Bnll
ORPN MSB
OOata
Entry
Soms
BnH
jtoxind Third
64H
111!
Sialu?
Second
Third
BnH
65H
mmH
gecond
06H
Third
vvH
n-MIDI
channel
:
OH
-
Fll (0
-
15)
0-ch.l I5"ch.l6
II
-
The
lower byte of the
paramder number designated by
RPN
mm
- The
upper byte of the parameter
number
designated by
RPN
vv - The
value of the parameter designated by
RPN
The
R-8M
receives the message on
the
channel set by
PATCll/PFM/ BASIC/
Receive Ch.
Z3R«caiva
Mouagat
to Control th«
System
Chann*) Voio*
M«1U9*
9
Program ehing*
Suius Second
CnH PPH
n • MIDI
channel
pp - Program number
;0H
- FH
(0
-
15)
0-Ch.l I5-ch.lC
T
OOH - 7FH
(0
-
127)
The
R-8M
receives the message on the channel
set
by
SETUP/MIDl/Control
Ch.
Upon
receiving this
message with
SETUP/MIDI/Pgm
Change
-
ON
selected,
the
K
-
8M
changes
Patch
and
Feel
Patch according
to
the program change map's contents
set
by
the
SETUP/PGM.
[Svatam
Common
Mams*
tSons
potition pointer
Parameters of a unit
can be changed by
using
MIDI
RPN' function.
De^gnaie Ihe
parameter
to
be changed by a
set
of
RPN MSB
and
l-SB.
and
then specify the
now
parameter value with Data
Entry.
Effective
RPN
for the
R-8M
is
Pitch
Bend
Sensitivity (RP,\
«0)
only.
Status
F2H
IIH
mm.ll
- Song
position
Hud
mmH
:
OOH,O0H -
7FH,7F1I
(0
-
16383)
This message syncs the Groove
to
the play information
when FEEL/RliGL/Regular
-
GROOVE
has been
selected.
MSB
I
.SB Rata entry Description
OOH 001!
vvH
Piidi
bend sensitivity
vv »
0-
12
semitone
steps,
up
to
I
octave
Upon
receiving this
message.
Ihe
R-8M
rewrites
PATCH/PFM/BASIC/Bend
Range
With the received
value.
Syitam
R*«l
Tim*
Maius*
•
Timing clock
Sl^t^is
F8H
tPitch
B«nd Ching*
Status
Second Thifd
Enil
III!
mmH
Status
FAH
n - MIDI channel
mm.H
•=
\'alue
:
OH
-
Fll (0
-
15) "
ch.l
15
-
ch.l6
:0OH,0OH - 7FII,7KH
{-8192 -
*819l)
The R
-
8M
receives Ihe
message on
the channel set
by
PATCH/ PFM/
BASIC/
Receive Ch.
Upon receiving
this
message with
SETUP/MIDl/Pitch Bender » ON
selected,
the R
-
8M
bends the
pitch
of
sounding
note according to the
value
set
by
PATCH/PI'M/
BASiC/Bend Range.
Channal
Moda MaiNga
#R*Mt
all
controllara
#Continua
Status
FBK
•Stop
Status
FCH
These messages syncs the groove to the play information
when FEEL/REG L/
Regular
= GROOVE
has been
selected.
gtalus
SsSfiDi!
Tti'"!
BnH 79H OOH
n < MIDI
channel
:0H -
Fll CO
-
15)
0-cIi.l
15-ch.l6
The
R - 8M
receives the
message on
the
channel
set
by
PATCH
/PFM/
BASIC/
Receive Ch.
The R - SM
initializes all
controllers
upon
receiving this
message.
Pitch
Bend Change
±
(center)
Panpot
Off
(PATCH/PFM/SOUND/Out
Asgn
is
activated)
Hold
1
Modulation
-iOH (the offset of assigned
parameter becomes
0.)
•
All
notvi
otr
Status
Second
Uuc!
BnH 7BH OOH
n = MIDI
channeNOH
-
FH (0 - 15) 0-ch.i I5"ch.i6
The
R - 8M
receives the
message on
the
channel
set
by
PATCH/PFM/BASIC/
Receive Ch.
Mutes
the
sounding notes upon
receiving
an
All
Nutcs
OH
message.
(Activa
Mnaing
FEH
Whenever
the
R-8M
receives this
message,
it
monitors the interval of the
coming
data.
If
the subsequent message has not arrived 300
ms
after
the previous
data,
it
processes
all
sections
as though
it
has
received
an
All
Notes Off
message and
a Reset
All
Controllers
message. Monitoring
of
incoming signals
is
terminated.
Sy*t*m
Exctutiv*
M««Mga
Status
FOH
:
System Exclusive
F7H
:
EOX
(End Of Exclusive)
With the
R - 8M,
the System Exclusive
Message
can be used to transmit
and
receive
parameters Of
Paldi. Feel
Patch and
Setup.
For
details refer to
"Roland Exclusive Messages"
and
paragraph
3.
123