Safety Instructions And Warnings - Black & Decker LD108 Instruction Manual

16 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c. When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws, or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a fire.
d. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
7. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by BLACK+DECKER,
the warranty will not be valid.
8. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
FEATURES (Fig. A)
1. Switch
2. Forward/reverse button
3. Torque Adjustment Collar
4. Keyless Chuck
5. Charging port
6. Screwdriver bit holder
7. Charger
8. Charging Indicator

SAFETY INSTRUCTIONS AND WARNINGS

BATTERIES
f Do not disassemble or open, drop (mechanical
abuse), crush, bend or deform, puncture, or shred.
f Do not modify or remanufacture, attempt to insert
foreign objects into the battery, immerse or expose
to water or other liquids, or expose to fire, excessive
heat including soldering irons, or put in microwave
oven.
f Only use the battery with a charging system specified
by the manufacturer/supplier.
f Do not short-circuit a battery or allow metallic or
conductive objects to contact both battery terminals
simultaneously.
f Dispose of used batteries promptly according to t.0he
manufacturer/supplier's instructions.
f Improper battery use may result in a fire, explosion, or
other hazard.
f Battery usage by children should be supervised.
Warning! Never attempt to open the battery for any
reason. If battery case is cracked or damaged, do not
insert into charger. Do not crush, drop or damage battery.
Do not use a battery or charger that has received a sharp
blow, been dropped, run over or damaged in any way
(i.e., pierced with a nail, hit with a hammer, stepped on).
Damaged batteries should be returned to service center
for recycling.
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
Construction
Earthing
Terminal
Safety Alert
Symbol
Revolutions
or Recipro-
cation per
minute