Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DigiTech dirty robot
Summary of Contents for DigiTech dirty robot
- Page 1 Dirty RObot OWNER’S MANUAL...
-
Page 2: Warranty
The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. - Page 3 3 different waveform and sub frequency options. To use the Dirty Robot pedal, enable the effect with the FOOTSWITCH (the LED will light when the effect is enabled). Set the MIX control to the 3 o’ clock position so you can hear the effect. Select a synth voice using the VOICE toggle switch at the top of the user interface.
-
Page 4: User Interface
Connect the specified Harman power supply (sold separately) to this jack. Be sure to use the proper power supply for your area’s mains line voltage. See ‘Specifications’ on page 9 for power supply model information. The Dirty Robot can only be powered using the external power supply. 3. DRIFT Knob This continuously variable knob rotates a full 360 degrees to control morphing between Sub, Octave, and Square waveforms. - Page 5 7. Input 2 Connect a second input to this jack for stereo operation. Inputs 1 and 2 are processed separately through the effect then fed to Outputs 1 and 2, keeping true stereo separation between channels. 8. Footswitch Turns the effect on or off. When this footswitch is pressed and held while the effect is enabled, it will modulate the synth effect signal.
-
Page 6: Making Connections / Applying Power
To connect the Dirty Robot pedal to your rig: 1. Turn down the amplifier’s master volume control. 2. Make all audio connections to the Dirty Robot as shown in ‘Connection Diagram’ on page 5. 3. Connect the appropriate Harman power supply (sold separately) to the POWER input connector and connect the other end to an available AC outlet. -
Page 7: Connection Diagram
Use only unbalanced TS instrument cables for audio connections. Optional NOTE: For best performance, place the Dirty Robot as close to the front of the signal chain as possible and bypass any effects that come before it when in use. -
Page 8: Example Settings
EXAMPLE SETTINGS Try these settings to get started. Tom Sawyer Tom Sawyer Living On A Prayer Living On A Prayer Tom Sawyer Tom Sawyer Living On A Prayer Living On A Prayer Cars Cars Mini Moog Mini Moog Cars Cars Mini Moog Mini Moog... - Page 9 PERFORMANCE ACCESSORIES The performance accessories make integrating the Dirty Robot pedal into any pedalboard a snap. The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) • StompLock™ (keeps your settings where you want them)
- Page 10 StompLock™ The included StompLock lets you lock your settings in place, while the open-top design lets you see your settings. To place the StompLock over the pedal knobs: 1. Set the knobs to your preferred settings. 2. Orient the StompLock so that it lines up with the knobs and gently push it over the top of the knobs.
-
Page 11: Specifications
SPECIFICATIONS Interface Controls: Mix, Modulation, Drift, Start, Stop, Sensitivity, Time, Effect on/off Footswitch Indicators: Effect on/off LED Jacks: Input 1 (Mono), Input 2, Output 1 (Mono), Output 2 Inputs Input Impedance: Effect on: >1 MΩ (stereo), >500 kΩ (mono) Effect off: >1 MΩ (stereo), >500 kΩ (mono) Effect off: True hardwire bypass Outputs Output Impedance:... - Page 12 PHONE: (801) 566-8800 WEB: digitech.com SUPPORT: digitech.com/en-US/support Dirty Robot Owner's Manual 5066300-A © 2016 Harman. All rights reserved. DigiTech is a registered trademark of Harman.