Error Messages - Panasonic DMR-ES20 Operating Instructions Manual

Error messages

On the television
Cannot finish recording
completely.
Cannot play.
Cannot record on the disc.
Unable to format.
Please check the disc.
Cannot record. Disc is full.
Cannot record. The number of
titles has exceeded the
maximum limit.
Error has occurred. Please
press ENTER.
No disc
Please change the disc.
This is a non-recordable disc.
This disc is not formatted
properly.
5
On the unit's display
RC
(" " stands for a number.)
Err
FULL
oooooo
U59
U99
RQT8152
38
Downloaded From Disc-Player.com Panasonic Manuals
•
The program was copy-protected.
•
The disc may be full.
•
There are already 99 recorded titles (
•
You inserted an incompatible disc (Discs recorded in PAL video, etc.).
•
The disc may be dirty or scratched.
•
Create space by erasing any unnecessary titles.
(Even if you erase recorded content from a DVD-R or +R, there is no increase in disc space.
Available disc space on DVD-RW (DVD-Video format) increases only when the last recorded
title is erased.)
•
Use a new disc.
•
Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering .
("oooooo" (self check) appears on the unit display.)
•
The disc may be upside down.
•
There may be a problem with the disc. Press [; OPEN/CLOSE] to remove it and check it for
scratches or dirt. (The unit turns off automatically after you open the tray.)
•
The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R,
DVD-RW (DVD-Video format) or +R.
•
You inserted an unformatted DVD-RAM or DVD-RW.
•
The operation is prohibited by the unit or disc.
•
The remote control and main unit are using different codes. Change the code on the remote
control.
Press and hold [ENTER] and the indicated number button at the
REC REC REC
same time for more than 2 seconds.
P TV
REC REC
When "Err" appears on the unit's display, the disc indicator
P TV
flashes.
•
The disc is dirty or badly scratched. The unit cannot record, play, or edit.
•
You have used a lens cleaner and it has finished. Press [; OPEN/CLOSE] to eject the disc.
•
You have inserted a disc the unit cannot play or record on.
•
You have inserted a DVD-RAM or DVD-RW that is unformatted or recorded on other
equipment.
•
If there is no change after turning the unit on and off, consult the dealer where the unit was
purchased.
•
There are already 16 timer programs. Delete unnecessary timer programs.
•
There was something unusual detected with the disc while recording, playing or transferring
(dubbing).
•
There was a power failure or the AC plug was disconnected while the unit was on. The unit is
carrying out its recovery process.
•
This process restores the unit to normal operation. The unit is not broken. Wait until the
message disappears.
The symbol "o" appears at the bottom left of the unit's display.
REC REC
The number of symbols increases one by one until six appear.
P TV
They then disappear one by one from the left until none remain.
This continues during self check.
•
The unit is hot.
The unit switches to standby for safety reasons. Wait about 30 minutes until the message
disappears.
Select a position with good ventilation when installing the unit. Do not block the vent on the
side of the unit.
•
The unit fails to operate properly. Press [POWER ^/I] on the main unit to switch the unit to
standby. Then press [POWER ^/I] on the main unit again to turn the unit on.
49 recorded titles).
+R
RAM -RW(V)
Page
—
—
—
—
42
21, 27, 30
—
—
—
42
4, 5
30
—
14
42
—
4, 5
30
—
19
—
—
40
—
—