DIGITAL LASER MFP SCX-4216F SCX-4116 SCX-4016 SERVICE Manual DIGITAL LASER MFP CONTENTS 1. Precautions 2. Reference Information 3. Specifications 4. Summary of product 5. Disassembly and Reassembly 6. Alignment and Adjustments 7. Troubleshooting 8. Exploded Views and Parts List 9. Block Diagram...
Page 2
ITSELF system f Samsung Electronics Co., Ltd. Printed in Korea. “http://itself.sec.samsung.co.kr” VERSION NO. : 1.00 CODE : JC-0095A - This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law. -...
VARNING - OSYNLIG LASERSTR LNING N R DENNA DEL R PPNAD OCH SP RREN R URKOPPLAD. BETRAKTA EJ STR LEN. STR LEN R FARLIG. VARO! - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA N KYM TT M LLE LASER- S TEILYLLE L KATSO S TEESEEN. Service Manual Samsung Electronics...
A fire can occur if unit is used under these conditions. (13) Do not insert steel or metal pieces inside/outside of the machine. Do not put steel or metal piece into the ventila-tor. An electric shock can occur. Service Manual Samsung Electronics...
Page 6
(4) Do use formal parts and same standardized goods when replacing parts. Must check the product name, part code, rated voltage, rated current, operating temperature, etc. (5) Do not use excessive force when looening or tightening of plastic parts. (6) Be careful not to drop small parts or objects in the machine. Service Manual Samsung Electronics...
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing together of clothing fabric and lifting one’s foot from a carpeted floor, can generate static electric- ity sufficient to damage an ESD. Service Manual Samsung Electronics...
Standard : For general home use, for medical service. Electronic Scale Standard: Equipment to check the weight of consumables supplied by Samsung Electronics. (The gram unit can be mea- sured.) Cleaning Equipments a IPA (Isopropyl Alcohol)dry cloth or a soft stuff neutral detergent.
Enhanced Parallel Port Read Only Memory firmware Second Cassette Feeder graphics device interface SMPS Switching Mode Power Supply ground SPGP Samsung Printer Graphic Processor Host Based Printing Samsung Printer Language Hard Disk Drive Spool Simultaneous Peripheral Operation Online high voltage Switch HVPS...
The sample pattern shown in below is the standard pattern used in a factory. The contents of the life span and the printing speed are measured with the pattern shown in below. (The picture in the manual is 70% size of the actual A4 size.) 2.3.1 A4 5% Pattern Service Manual Samsung Electronics...
Page 11
R E F E R E N C E I N F O R M AT I O N 2.3.2 A4 2% Pattern Service Manual Samsung Electronics...
Page 12
R E F E R E N C E I N F O R M AT I O N 2.3.3 A4 IDC 5% Patten Service Manual Samsung Electronics...
Page 13
R E F E R E N C E I N F O R M AT I O N Service Manual Samsung Electronics...
Remarks Compatibility Win 3.x Win 95 Win 98&WinME Win NT 4.0 Win 2000 Win XP WHQL for Printer Only Mac Printer Only Linux Driver Printer TWAIN PC-FAX PC Fax is only avail- able through PC Modem Service Manual Samsung Electronics...
Page 20
Items Descriptions Remarks Type Single Cartridge How to install Front door open and front loading Toner Life Initial 1,000 sheets Initial toner life could running 3,000 sheets be different accroding to country Level Sensor Toner Count Service Manual Samsung Electronics...
Page 21
Specifications Service Manual Samsung Electronics...
SUMMARY OF PRODUCT 4.1.3 Control Panel < SCX-4216F > Adjusts the brightness of the documents for the current copy job. Selects the document type for the current copy job. Allows you to use special copy features, such as Clone, Collation, Auto fit, 2-side, N-up (multiple pages on a sheet) and Poster copying.
Page 25
Allows you to save on toner by using less toner to print a document. Allows you to save on call costs by sending a fax at a preset toll-saving time. Using this feature, you can take advantage of lower long distance rates at night, for example. Service Manual Samsung Electronics...
Page 26
N-up (multiple pages on a sheet) and Poster copying. Makes a copy smaller or larger than the original. Selects the number of copies. Allows you to save on toner by using less toner to print a document. Service Manual Samsung Electronics...
The pressure roller mounted right under the heat roller is made of the silicon resin, and the surface of the roller is coated with Teflon to fuse the toner on the paper when paper passes between the heat roller and the pressure roller. 4.2.4.5 Safety Relevant Facts Service Manual Samsung Electronics...
Page 28
• Image Processor Specification 1.Operating frequency: 66MHz 2.Image sensor interface: 200/300/600 dpi CIS or CCD 3.Line time: Copy, FAX, Binary (Lineart, Halftone) PC Scan: 1.5ms/Line Color PC Scan (Grey, 256 Color, True Color): 4.5ms/Line 4.A/D conversion: 10bit conversion Service Manual Samsung Electronics...
Page 29
/HS YNC signal to arrange the vertical line of the image on the paper. After detecting the /HS YNC signal, the image data is sent to the LSU to arrange the its left margin on the paper. The one side of the polygon mirror is one line for scanning. Service Manual Samsung Electronics...
- Management of disusable toner: Collect the toner by using electric static (Clenerless Type- No disusable toner) - OPC Drum protecting Shutter: None - Classifying device for toner cartridge: ID is classified by interruption of the frame channel. Service Manual Samsung Electronics...
SUMMARY OF PRODUCT 4.3.1 ASIC (Chorus2) Samsung’s S3C46Q0X 16/32-bit RISC micro controller is designed to provide a cost-effective, low power, small die size and high performance micro-controller solution for MFP. The S3C46Q0X is developed using ARM7TDMI core, 0.18(m CMOS standard cell, and memory cell.
The motor driving circuit is formed when the Driver IC is selected. The A3977 (Motor driver IC) is used in this case. The resistance Rs value of sensing and the voltage value of the V reference can be changed by the motor driving voltage value. Service Manual 4-12 Samsung Electronics...
Page 34
The HVPS part takes the 24V and outputs the high voltage for THV/MHV/BIAS, and the outputted high voltage is supplied to the toner, OPC cartridge, and transfer roller. Service Manual 4-13 Samsung Electronics...
Page 35
- Error: 1. If SUP is GND, a density is dramatically going down. 2. If SUP is floating due to instable contacting point of terminal, and etc., a density is signif- icantly going down as much as it cannot be recognized with eyes. Service Manual 4-14 Samsung Electronics...
Page 36
AVG : 95 Wh PRINTING 1.5 A 0.5A 1.5 A 1.0 A AVG : 350 Wh Sleep-Mode 0.3A 0.0A 0.0A 0.06A AVG : 20 Wh 4) Length of Power Cord : 1830 ± 50mm 5) Power Switch : Service Manual 4-15 Samsung Electronics...
1) Triac (THY1) feature - 12A,600V SWITCHING 2) Phototriac Coupler (PC3) - Turn On If Current : 15mA ~ 50mA(Design: 16mA) - High Repetive Peak Off State Voltage : Min 600V Service Manual 4-16 Samsung Electronics...
Page 38
AD converter. The voltage value for impressing to the transfer roller is decided by the changed value. Service Manual 4-17 Samsung Electronics...
Page 39
Error Description Polygon motor error When the polygon motor’s speed doesn’t become a normal Hsync error The polygon motor’s speed is normal, but the Hsync signal is not created. Service Manual 4-18 Samsung Electronics...
OPE board is consisted of various function keys and LCD to display an operation of key. MICOM creates a circuit with using HT48R50 MICOM of HOLTEC CO. and applies LED and LCD. A communication method with a CPU of a main board is UART, and related signals are /Reset, TXD, and RXD. Service Manual 4-19 Samsung Electronics...
3. Unplug the power cord. 4. Use a flat and clean surface. 5. Replace only with authorized components. 6. Do not force plastic-material components. 7. Make sure all components are in their proper position. Service Manual Samsung Electronics...
3. Unlatch the (Cover Face Up) securing the Rear cover, as shown below.Then lift the (Cover Face Up) out. Cover Face Up 2. Remove the Rear Cover from the Frame Ass'y and Scanner Ass'y. Rear Cover Service Manual Samsung Electronics...
Page 43
3. Lift the LH and RH Side Cover out in the direction of should remove: arrow. - Rear Cover (see page 5-2) Side Cover(LH) 2. Unplug the Speaker Harness, as shown below. Speaker Harness Side Cover(RH) Service Manual Samsung Electronics...
Disassembly and Reassembly 5.4 Front Cover 1. Take out the Cassette. 3. Unlatch the Front Cover securing the Frame Ass'y. Then remove the Front Cover, as shown below. Cassette Front Cover 2. OPen the Front Cover. Service Manual Samsung Electronics...
Page 45
2. Remove the two screws securing the Scanner Ass'y, as shown below. 3. Unplug the 6 connectors from the Connector PBA , as 5. Pull the Platen Cover upward and remove it. shown below. Connection Board Connection Board Service Manual Samsung Electronics...
Page 46
7. Lift the OPE Unit out. Then unplug the two connec- tors from the OPE Unit and remove it. 9. Unlatch the Scan Upper securing the Scan Ass’y Then pull the Scan Upper upward and remove it. Scan Upper Service Manual Samsung Electronics...
Page 47
Module. Scanner Module CCD Cable CCD Shaft Belt Holder 11. Push the Belt Holder and take out the Belt, as shown 13. Remove the Reduction Gear and Idle Gear, as below. shown below. Belt Gear-Timing Gear-Reduction Service Manual Samsung Electronics...
Page 48
14. Remove the two screws and take out the Motor 16. Unlatch the Open Sensor and remove it, as shown Bracket. below. Motor Bracket Open Sensor 15. Unplug the one connector from the Open Sensor Ass'y. Service Manual Samsung Electronics...
Page 49
Motor Ass'y. Open Cover ADF Motor Ass’y ADF Lower Ass’y 4. Pull the White Bush, then rotate it until it reaches the slot, as shown below. Then lift the Pick-Up Ass'y out. Pick up Ass’y White Bush Service Manual Samsung Electronics...
- Scanner Ass’y (see page 5-5) 2. Remove the six screws securing the OPE PBA from the OPE Cover. OPE Cover OPE PBA Key Pad 3. Remove the Contact Rubber from the OPE Cover. Contact Rubber Service Manual 5-10 Samsung Electronics...
Page 51
.5. Remove the Exit Gear and Bearing, as shown below. Exit Gear Bearing 3. Unlatch the Top Cover Securing the Frame Ass'y, Exit Roller using a proper tool as shown below. Then lift the Top Cover out. Top Cover Service Manual 5-11 Samsung Electronics...
Page 52
- Scanner (see page 5-5) 2. Remove the two screws securing and unplug the FPC cable From the Main PBA. Then reomve the LIU PBA LIU PBA Engine Shield Ass’y 2. Unplug two connector. Thermistor connector Fan Connector Service Manual 5-12 Samsung Electronics...
- Side Cover(LH, RH) (see page 5-3) - Scanner (see page 5-5) - Engine Shield Ass’y(see page 5-10) 2. Unplug the one connector and remove the five screws securing the Main PBA. Then lift the Main PBA out, as shown below. Service Manual 5-13 Samsung Electronics...
Page 54
SMPS - Engine Shield Ass’y(see page 5-12) 2. Remove the three screws securing the Inlet Bracket and remove it Inlet Bracket 2. Unplug the one connector and remove the one screw securing the Engine Shield. Service Manual 5-14 Samsung Electronics...
Page 55
Idle Gear 3. Remove the two screws securing the Thermostat. Then lift the Thermostat out Thermostat 6. Remove the four screws securing the Fuser Cover and remove it, as shown below. Claw Fuser Cover Service Manual 5-15 Samsung Electronics...
Page 56
Disassembly and Reassembly 7. Unwrap the Thermister Harness, as shown below. 8. Remove the one screw securing the Thermister and remove it, as shown below. Thermister Harness Thermister Service Manual 5-16 Samsung Electronics...
Page 57
1. Before you remove the Fan, you should remove: 2. Unplug the connector from the SMPS and remove the - Rear Cover (see page 5-2) one screw. Then take out the Fan. - Side Cover (RH) (see page 5-3) DC Fan Service Manual 5-17 Samsung Electronics...
Page 58
3. Take out the Drive Ass'y, then unplug the connector remove: from the Main PBA, as shown below. - Rear Cover (see page 5-2) - Side Cover (LH) (see page 5-3) 2. Remove the six screws securing the Drive Ass'y. Drive Ass’y Service Manual 5-18 Samsung Electronics...
Page 59
- LSU (see page 5-18) 2. Remove the three screws securing the Transfer Earth and remove it. Transfer Earth 4. Unlatch the Bushing and remove it. Then lift the Transfer Roller out, as shown below. Transfer Roller Bushing Service Manual 5-19 Samsung Electronics...
Page 60
Guide paper 5. Remove the Idle Gear and Feed Gear2. Feed Gear2 3. Pull up the Feed Idle Bushing and Feed Idle Shaft, as shown below. Feed Idle Idle Gear Shaft Bushing Service Manual 5-20 Samsung Electronics...
Page 61
Disassembly and Reassembly 6. Remove the Feed Gear1 Ass'y. 7. Pull up the Feed Roller and Feed Roller1. Feed Roller Feed Gear1 Ass’y Feed Roller1 Service Manual 5-21 Samsung Electronics...
Page 62
Bush 5. Remove the two screws securing the Manual Solenoid and Pick-Up Solenoid. Then remove Manual Solenoid and Pick-Up Solenoid. 3. Remove the Pick-Up Gear Ass,y. (Pick up) Solenoid Pick up Gear (Manual) Ass’y Solenoid Service Manual 5-22 Samsung Electronics...
It includes the contents of manual. 6.1 Paper path Scanner Part ADF-Roller Pickup-Roller Doc-Paper(30Sheets) ADF-Idle Roller Sensor-Regi Sensor-Regi Sensor-Doc Sensor-Doc Exit-Roller Feed-Roller Sensor-Scan Sensor-Scan White-Sheet White-Sheet CCD-Module Engine Part L S U Fuser Toner Cartridge Service Manual Samsung Electronics...
Engine Part L S U Fuser Toner Cartridge Paper Input (Cassette) Paper Empty Sensor (Cassette) Paper Input (Manual Feeder) Paper Feeding Sensor Paper Out (Face Down) Paper Exit Sensor Paper Empty Sensor (Manual) Service Manual Samsung Electronics...
Page 65
Paper Jam0 Paper Jam1 L S U L S U Fuser Fuser Toner Cartridge Toner Cartridge EXIT EXIT Sensor Sensor MP Sensor MP Sensor Feed Feed Sensor Sensor Empty Sensor Empty Sensor Paper Jam2 Bypass Jam Service Manual Samsung Electronics...
Page 66
ALIGNMENT & ADJUSTMENTS 6.2.1 Clearing Document Jams(For SCX-4216F/SCX-4116 only) If a document jams while it is feeding through the ADF (Automatic Document Feeder),“DOCUMENT JAM ” appears on the display. 6.2.1.1 Input Misfeed 1) Open the ADF top cover. 3) Close the ADF top cover.Then load the documents back into the ADF.
Page 67
ADF or the feed area by carefully pulling it towards the right by using both hands. 3) Close the document cover.Then load the documents back into the ADF. Service Manual Samsung Electronics...
Page 68
3) Remove the jammed paper by gently pulling it straight out. If there is any resistance when you pull the paper or the paper is not seen in this area,skip to the fuser area around the toner cartridge Service Manual Samsung Electronics...
Page 69
5) Close the rear cover. 6) Open and close the front cover to resume printing. 3) If there is any resistance when you pull the paper or the paper is not seen in the front output tray,open the rear cover. Service Manual Samsung Electronics...
Page 70
NOTE : The fuser area is hot.Be careful when removing paper from the machine. 1) Open the front cover and remove the toner cartridge. 3) Replace the toner cartridge and close the front cover. Printing automatically resumes. 2) Remove the jammed paper by gently pulling it straight out. Service Manual Samsung Electronics...
• Do not mix paper types in the paper tray.. • Use only recommended print materials..See “Paper Specifications ” • Ensure that the recommended print side is facing down when loading paper in the paper tray and facing up in the Bypass tray. Service Manual Samsung Electronics...
In the service manual, the items are about the possible set-up by user. 6.Reports 1.Paper Setting 2.Copy Setup System Data Paper Tray Change Default Paper Size Timeout 9.Maintenance 8.Machine Setup Clean Drum Language Clear Memory Power Save CCD Power Save USB Mode Service Manual 6-10 Samsung Electronics...
Page 73
ALIGNMENT & ADJUSTMENTS 6.4 User Mode(SCX-4216F) The table in the bellow explains the possible setting functions by user. The details about the ways to use are explained in the user manual. In the service manual, the items are about the possible set-up by user.
In service (tech) mode, the technician can check the machine and perform various test to isolate the cause of a malfunction. While in Tech mode, the machine still performs all normal operations. 1)To enter the Tech mode (SCX-4216F) To enter the Tech mode, press in sequence, and the LCD briefly displays ‘TECH’, the machine has entered service (tech) mode.
NOTICE : Always perform the memory clear after replacing the main board. Otherwise, the system may not operate properly. FLASH UPGRADE The Firmware Upgrade function and has two methods, Local and Remote. More information can be found in the firmware upgrade items. Service Manual 6-13 Samsung Electronics...
3. After the scan, CCD SHADING PROFILE will be print out. 4. If the printed image is different to the image, the CCD is defect. NOTICE : When you test CCD, make sure that the cover is closed. Service Manual 6-14 Samsung Electronics...
Use this list to check for send and receive errors. If a communication error occurs while the machine is in TECH mode, the protocol list will print automatically. SYSTEM DATA This list provides a list of the user system data settings and tech mode settings. Service Manual 6-15 Samsung Electronics...
LCD. It is classified in 5. items (0~4), and the functions of items are as bellows. 6.6.1 To enter the Engine Test Mode 1)To enter the Engine Test mode (SCX-4216F) Press in sequence, and the LCD briefly displays ‘Engine Test’, the machine has entered Engine Test Mode.
Page 79
ALIGNMENT & ADJUSTMENTS 6.7 Identify Sale Date(Only SCX-4216F) This function confirms the date that consumer bought product and used the product for the first time. When the consumer first operate the machine, it will start a scan and page count.
Black spot Supply Roller 37.0mm Horizontal density band Develop Roller 35.2mm Horizontal density band Transfer Roller 45.3mm Black side contamination/transfer fault Heat Roller 66.3mm Black spot and fuser ghost Pressure Roller 75.5mm Black side contamination Service Manual 6-19 Samsung Electronics...
Page 82
ALIGNMENT & ADJUSTMENTS Service Manual 6-20 Samsung Electronics...
Shaft-Pickup. shaft-pickup and housing-pickup become open or is broken away. 5. If the paper feeds into the printer rand Jam 0 occurs, perform DCU to check feed-sensor of the engine board. Service Manual Samsung Electronics...
Page 84
3. Remove the jammed paper after disas- sembling the fuser : Clean the surface of the pressure roller with dry gauze. • Remove the toner particles stained on the rib. • Check the assemblage and perfor- mance of the exit. Service Manual Samsung Electronics...
(Background, Hot off set) Heat-roller and Thermistor and remove the foreign matter off of the pressure roller. 2. If background appears badly in the printing, fix it by referring to the solutions for background. (See 4.5.8 Background) Service Manual Samsung Electronics...
1. Replace the contaminated or damaged part. aged. 2. Check if the document sensors of ADF Ass’y 2. If you cannot confirm the damaged part with the (3 paper sensors) are normal. naked eye, try to replace the ADF Ass’y. Service Manual Samsung Electronics...
Page 87
2. Confirm to catch a click sound, while a key on the OPE 2. Even after the key has been replaced, it is still wrong, panel is pressed on. try to replace the OPE Ass’y and the Main B'd in sequence. Service Manual Samsung Electronics...
Check and Cause Solution 1. Bending or deformation of the actuator of the paper sen- 1. Replace the defective actuator. sor. 2. The function of the Main PBA is defective Perform. 2. Replace the Main PBA. Service Manual Samsung Electronics...
Check and Cause Solution Check the Connector(CN1) and Circuit of the Cover Switch 1. Check the insertion of the Door S/W Connect. department in the Main PBA. 2. Replace the Main PBA or Door Open S/W. Service Manual Samsung Electronics...
1. Replace the power supply cord or SMPS. 2. Check for defective of LED-Panel on the front-cover if the 2. Replace the control board. LED of Panel does not appear after normal warming-up. 3. Replace the LED-panel. Service Manual Samsung Electronics...
Page 91
1. If the supply of +24v is unstable in the Main Control board 1. Replace LSU. linking with LSU, check drive by Engine Test Mode : Diagnostic Code 1 LSU Motor on. 2. Replace the Main Control board. Service Manual Samsung Electronics...
4. No. 4. : Open the front cover and check odically at the top of a black image. ribs that corresponds to the position of the voids. Remove if found. 5. If the problems are not solved, replace the developer cartridge. Service Manual 7-10 Samsung Electronics...
1, take measures as to replace the develop- er cartridge and try to print out. 5. Clean the inside of the set against the paper particles and foreign matter in order not to cause the trouble. Service Manual 7-11 Samsung Electronics...
Digital Printer the bad contacts between power supply in the side of the Developer and charge terminal of HVPS. 3. If steps 1 and 2 above did not correct the problem, replace the HVPS . Service Manual 7-12 Samsung Electronics...
3. The up-to-down movement of the trans- 3. Clean the busing on the transfer roller. fer roller is swift? 4. The HVPS is normal? 4. Replace the HVPS. (Perform Engine Test Mode diagnostic code 4) Service Manual 7-13 Samsung Electronics...
Page 96
Select 'Thick Mode' on paper type menu from mal paper or transparencies such as OHP, the software application and after use, we rec- Digital Printer higher transfer voltage is required. ommend returning to the original Mode. Digital Printer Digital Printer Digital Printer Service Manual 7-14 Samsung Electronics...
Page 97
2. If the transfer roller is contaminated, run PC Digital Printer on the face of page will occur. Cleaning Mode Print 2 or 3 times. Digital Printer And perform Self-Test 2 or 3 times to remove contamination. Service Manual 7-15 Samsung Electronics...
Page 98
Mode diagnostic Mode code 0 if the Solenoid is normal. 3. If not solved by the above directions 1-2, Replace the engine board. 4. Turn the power off, clear the print job on the computer, and try printing again. Service Manual 7-16 Samsung Electronics...
3. Check the connection of HARNESS between the 3. The problem still persists, then replace the LIU and the LIU and the Main PBA. main B'd in sequence. Notes: Product supports the MF DIAL type only. Service Manual 7-17 Samsung Electronics...
2. Check the RECEIVE condition by trying to forward a FAX to another fax machine from the forwarding side FAX. 3. Check if the telephone line connected to the Product is contaminated or gets stripped off or down. Service Manual 7-18 Samsung Electronics...
Page 101
Solution Check if the RECEIVE Mode is TEL MODE or FAX Even when the RECEIVE Mode is changed to FAX MODE. MODE, it cannot receive, then replace the LIU and the Main B'd in sequence. Service Manual 7-19 Samsung Electronics...
1. If the RECEIVE Mode is set to the TEL MODE, reset it MODE. to the FAX MODE. 2. Even after the RECEIVE Mode is changed to the FAX Mode, it cannot receive, then try to replace the LIU and the Main B'd in sequence. Service Manual 7-20 Samsung Electronics...
Black page is printed out when Copy. Check and Cause Solution 1. Check the CCD problem in Main PBA. 1. Check the CCD harness contact. 2. Check shading profile. 2. Remake shading profile in the tech mode. Service Manual 7-21 Samsung Electronics...
1. Remake shading profile in the tech mode. 2. The gap above 0.5 mm can cause a blurred image. 2. Check the gap between original and scanner glass. 3. See “Print” troubleshooting. 3. Check printing quality. Service Manual 7-22 Samsung Electronics...
2. Check if the resolution is set too low in PC Scan 2. If the resolution is set to low, let the user be acquaint- options. (Refer to User's Manual.) ed with the using method well. Service Manual 7-23 Samsung Electronics...
Page 106
7.7 Toner Cartridge Service It is not guaranteed for the default caused by using other toner cartridge other than the cartridge supplied by the Samsung Electronic or caused by non-licensed refill production. 7.7.1 Precautions on Safe-keeping of Toner Cartridge Excessive exposure to direct light more than a few minutes may cause damage to the cartridge.
(1)Check whether foreign sub- stances or toner are stuck to the terminal (contact point) of the developer. (2)Check whether the state of the terminal assembly is normal. 3. If it cannot be recycled: Replace the developer. Service Manual 7-25 Samsung Electronics...
Page 108
2 times. (2) Check whether the state of (2) If toner nearly being expired the terminal assembly is are collected to use, it is normal. judged as the recycled devel- oper. Service Manual 7-26 Samsung Electronics...
Page 109
Clean the terminals of the (point of contact) of the developing roller, then recheck it. developer and the state of assembly. (Especially check the devel- oping roller terminal.) Service Manual 7-27 Samsung Electronics...
EXPLODED VIEW & PARTS LIST 8.1 Main Assembly Service Manual Samsung Electronics...
Page 112
EXPLODED VIEW & PARTS LIST Main Assembly Parts List SA : Service Available O : Service available X : Service not available Description SEC.Code Q’ty Remark SCX-4216F / SCX-4116 / SCX-4016 ELA HOU-UNIT SCAN JC96-02669A SCX-4216F ELA HOU-UNIT SCAN(4116) JC96-02790A SCX-4116 ELA HOU-UNIT SCAN...
Page 113
SA : Service Available O : Service available X : Service not available Description SEC.Code Q’ty Remark 17-3 PPR-SPACER_TR JC72-00851A CBF SIGNAL-LIU JC39-00270A SCX-4216F Only PBA SUB-LIU_USA_EXT JC92-01481C SCX-4216F Only ELA-TONER UNIT PLATE-P-CHANNEL JC61-00606A PBA SUB-CONN JC81-01718A CBF HARNESS-ENGINE JC39-00240B...
Page 114
O : Service available X : Service not available Description SEC.Code Q’ty Remark ELA UNIT-RX DRIVE JC96-02733A BRACKET-P-GEAR 1400 GEAR-RDCN 53/26 JC66-00388A GEAR-RDCN 113/33 JC66-00391A GEAR-RDCN 57/18 JC66-00389A WASHER-PLAIN BRACKET-P-MOTOR 1400 GEAR-RDCN 103/41 JC66-00390A GEAR-RDCN 90/31 JC66-00392A MOTOR STEP-HUMMINGBIRD JC31-00028A PMO-IMPELLER_DRV Service Manual Samsung Electronics...
Page 116
EXPLODED VIEW & PARTS LIST 4-3-2 4-3-5 4-3-4 4-3-3 4-3-1 Service Manual Samsung Electronics...
Page 117
RING-C 2-19 GUIDE-STACKER SUB JC61-00712A SCREW-TAPTITE 6003-000196 ELA HOU-ADF MOTOR JC81-01701A BRACKET-GEAR JC61-00776A MOTOR BLOWER-ADF JC31-00023A GEAR-CLUTCH 29 JB66-00101A PMO-WHITE CLUTCH SUB 29 JB72-00844A GEAR-CLUTCH 39 JC66-00322A RING-C 6044-000159 GEAR-IDLE 35 ADF JC66-00458A GEAR-40/21 ADF JC66-00456A Service Manual Samsung Electronics...
Page 118
PMO-ROLL PINCH JG72-40663A SHAFT-STACKER JC66-00594A MEA UNIT-HINGE JC97-01707A RPR-ROLLER EXIT IDLE JC73-00091A ICT-SHAFT PINCH JF70-40521B SCREW-TAPTITE 6003-000196 MEA UNIT-COVER OPEN(LEX) JC97-01706A COVER-M-OPEN(LEX) JC63-00147A PMO-GUIDE PAPER JB72-00843A MEA UNIT-PICKUP JC97-01705A PMO-BUSHING WHITE JF72-41306A GEAR-ADF 38 JB66-00103A RING-C 6044-000159 Service Manual Samsung Electronics...
Page 119
EXPLODED VIEW & PARTS LIST 8.4 OPE Unit Assembly(SCX-4216F) Service Manual 8-10 Samsung Electronics...
Page 120
EXPLODED VIEW & PARTS LIST OPE Unit Assembly Parts List(SCX-4216F) SA : Service Available O : Service available X : Service not available Description SEC.Code Q’ty Remark ELA HOU-OPE JC81-01695A COVER-M-OPE(4IN1) JC63-00153A KEY-M-RESOLUTION JC64-00059A KEY-M-COPY JC64-00054A KEY-M-SCROLL JC64-00056A KEY-M-STOP JC64-00055A...
Page 121
EXPLODED VIEW & PARTS LIST 8.5 OPE Unit Assembly(SCX-4116/4016) Service Manual 8-12 Samsung Electronics...