Page 1
Sweeper Operation Manual Machine no. Models KM 70 G Type 02 KM Domus Type 02 KM 80 G Type 02 KM 100 G Type 02 Original Operation Manual 12-2014 Sweeper 689.04-40...
Contents Important Information .......................... 3 General ..........................3 Symbols ..........................3 Limitation of liability ........................ 3 Copyright ..........................3 Warranty ..........................3 Safety ..............................4 Use in compliance with intended purpose................4 Possible misuse ........................4 General sources of risks ......................4 2.3.1 Use and operation ....................
Important Information We are pleased that you have selected a machine from Symbols Cramer GmbH in Germany. Please read this Operation Manual before you use the DANGER ! machine for the first time and observe the notes and This symbol cautions against an immediate safety instructions.
Safety • Immediately remove spilled fuel with a cloth - danger of Use in compliance with intended purpose life by burning and explosion. The machine is approved as a sweeper for sweeping • Keep fuel in designated containers. and collecting (with fitted sweepings container) •...
Safety instructions Safety devices • Do not remove any covers during operation. The assembly and safety instructions • Immediately remedy any damage to safety devices. must be read and observed prior to starting the machine. Behaviour in case of fire Risk by flinging parts with running motor.
Operating elements for all models 1. Drive Lever on the right for operation drive Lever released: Machine is at standstill Lever activated: Machine moving 2. Brush drive lever Lever on the left for brush activation Lever released: Brush is at standstill: Lever activated: Brush turns 3.
Operating elements for KM Domus 4. Hand throttle for motor capacity Parking brake on support Brake on: Push the lower lever down wheel with your foot Brake off: Push the upper lever down with your foot 8. Release and tilt back steering bracket 1.
Working position and areas of risk Working position: Behind the machine on the handles Areas of risk: • Catchment area of sweeping brushes • Ejection area of sweeping brushes Accessories and spare parts Original parts Only original spare parts and original accessories may be used. Delivery, transport, storage Delivery Transport...
Operation Activities prior to use Brush setting Height setting of sweeping brush by adjusting the support Basic setting wheel: Height of sweeping brush is set • The bristles of the sweeping brushes should just touch Fuel tank is filled the ground Throttle is set to STOP/off.
Maintenance Safety DANGER ! Risk of injury by inappropriately performed maintenance work! Defective work may result in serious bodily injuries and damage to property. Make sure that you have sufficient working space. Place components separately. Remount all components. Remount all safety covers. Keep the risk area clear of persons.
Operation Manual cover). 3. Determine the failure cause. 4. Remedy failure or contact specialist dealer. Spare parts designations and spare parts lists are provided for download on our website www.cramer.eu. First action for troubleshooting Failure / Error message Remedy Notes Check throttle position (START).
Technical data KM Domus KM 70 G KM 80 G KM 100 G Type 02 Type 02 Type 02 Type 02 Machine data Length x Width x Height, cm 86 x74x75 89x71x76 89x81x76 89x101x76 Deadweight (transport weight), kg Drive speed Forward km/h Backward km/h Brush speed...
10 Declaration of conformity EU Declaration of conformity pursuant to machine directive 2006/42/EC Annex II 1-A The authorized party with residence in the EU, Cramer GmbH Reimersstr. 36 26789 Leer herewith declares, that the following product Manufacturer: Cramer GmbH Reimersstr. 36...
11 Sweeping brush installation, Side cover installation Sweeping brush installation for KM Domus, KM 100 G Delivery, packaging, assembly Risk of high dead weight • The machine must not be lifted manually. • Pull the machine off the transporter by its handles. ATTENTION! •...
Page 15
1. Left brush overview 1. Left brush Left brush 2. Washer 3. Washer with nibs 2. Press-fit the washer 1. Washer with nibs with nibs (no. 1) into 2. Washer the hollow body recess 3. Recess of the left brush. Lightly hit on it as needed.
Page 16
Side cover installation for KM Domus, KM 100 G Overview 1. Brush 2. Threaded rod 3. Side cover, left and right (rubber) Assemble side As to item 3: covers on the left 1. Position the rubber side covers over the cover plate holes as and right indicated in the drawing.
Need help?
Do you have a question about the KM 70 G Type 02 and is the answer not in the manual?
Questions and answers