Application Advice; Maintenance & Service; Declaration Of Conformity - Skil 4270 Original Instructions Manual

! always select "all/curve" when sawing splinter-
sensitive material
• Adjusting sawing speed to material used 0
! if the tool does not run with wheel D in position 1,
select a higher sawing speed and lower the
sawing speed while the tool runs
• Dust suction !a
! do not use vacuum cleaner when cutting metal
• Dust blowing !b
• Spot light @ (4370)
• Operating the tool
- before switching on the tool, ensure that front end of
footplate rests flat on the workpiece
- hold tool firmly with both hands, so you will have full
control of the tool at all times
! while working, always hold the tool at the
grey-coloured grip area(s) #
- ensure that complete surface of footplate rests firmly
on the workpiece
! ensure that the blade has come to a complete
standstill, before you lift the tool from the
workpiece
- keep ventilation slots G 2 uncovered

APPlICATION ADVICE

• Use the appropriate saw blades $
! use T-shank blades only %
• When cutting metals, lubricate saw blade regularly with oil
• For an accurate straight cut, guide tool with footplate
along the edge of a straight piece of wood ^
• Pre-drill a hole before making cut-outs &
• Splinter-free cutting
- cover cutting-line with several layers of wide tape
before cutting
- always face the good side of the workpiece down
• For more tips see www.skil.com
mAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots G 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONmENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol * will remind you of this when the need for
disposing occurs

DEClARATION OF CONFORmITY

• We declare under our sole responsibility that the product
described under "Technical data" is in conformity with the
following standards or standardization documents: EN
60745, EN 61000, EN 55014, in accordance with the
provisions of the directives 2004/108/EC, 2006/42/EC,
2011/65/EU, 2009/125/EC (EU regulation 1194/2012)
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
11.09.2013
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 90 dB(A) and the sound
power level 101 dB(A) (standard deviation: 3 dB), and the
vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)
✱ when cutting wood 5.6 (4270) / 8.8 (4370) m/s²
✱ when cutting metal 6.7 (4270) / 13.3 (4370) m/s²
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns
Scie sauteuse
INTRODUCTION
• Cet outil est conçu pour effectuer des découpes et
coupes dans le bois, les matières plastiques, le métal, les
plaques en céramique et le caoutchouc, et est approprié
pour des coupes droites et curvilignes à 0° ou 45°
• L'éclairage de cet outil électroportatif est destiné à
éclairer l'espace de travail de l'outil; il n'est pas conçu
pour servir de source d'éclairage ambiant dans une pièce
(4370)
• Cet outil n'est conçu pour un usage professionnel
• Lisez et conservez ce manuel d'instruction 3
10
4270/4370