Table of Contents
Advertisement
40
150S4 LCD
Go to cover page
White Balance Adjustment
Alignment procedure
1. Turn on 150S4 LCD monitor.
2. Turn on the Timing/Pattern generator. See Fig. 1
Setting generator to provide CROSS-Hatch pattern at
Resolution :
1024 x 768
Timing :
H= 48 KHz
V= 60 Hz
3. Preset LCD colour Analyzer CA-110
- Remove the lens protective cover of probe CA-A30.
- Set Measuring/viewing selector to Measuring position for reset
analyzer. (Zero calibration) as Fig. 2
- Turn on the colour analyzer (CA-110).
- Press 0-CAL button to starting reset analyzer . See Fig. 3
Fig. 1
0-CAL
4. Entering factory adjustment mode of LCD Monitor.
- To hold
and
buttons then power on the monitor. Press
to bring up OSD menu for confirmation.
HUDSON3 150S4 T106 20021024
Factory mode
Note : after alignment, please reset OSD to user s mode for normal
operation. Otherwise, the monitor won t entering power saving
mode and showing full white picture all the time as no video
signal supplied. To leave factory mode by restart the monitor.
Colour Adjustment
cover (black)
cover (black)
Measurement/viewing selector
Measurement/viewing selector
Fig. 2
Fig. 3
5. Adjust OSD menu to lower position of screen (i.g. adjust V-position to
value 0 at submenu of OSD Setting.
6. Setting Brightness and Contrast
- Adjust Brightness to value 70 .
- Adjust Contrast to value 50 .
7. Switch light probe to V iewing position.
8. Move the Lens barrel forward or backward to get clear image as
shown in Fig. 4
9. Switch light probe to Measuring position. It should be able to
indicate colour value on the CA-110.
Measurement/viewing selector
Measurement/viewing selector
Fig. 4
10. Setting pattern to full white picture.
11. Press
then select hudson3 150S4 t106 20021024 by
12. Press
to bring up submenu as following windows.
HUDSON3 150S4 T106 20021024
BL
BL
: 0
: 0
SUB - BRI :
SUB - BRI :
170 255
170 255
SUB - CON :
SUB - CON :
100 130 160
100 130 160
9300 K
9300 K
0
0
: R 209 G 203 B 255
: R 209 G 203 B 255
0
0
6300 K
6300 K
: R 242 G 237 B 255
: R 242 G 237 B 255
SRGB
SRGB
: R 208 G 208 B 208
: R 208 G 208 B 208
OFFSET2 : R 92 G 82 B 77
OFFSET2 : R 92 G 82 B 77
GAIN
GAIN
: R 133 G 134 B 132 255 m 200
: R 133 G 134 B 132 255 m 200
AUTO-SUB :
AUTO-SUB :
OSDTIMER 60
OSDTIMER 60
OK
VCOM
VCOM
: 120
IDX : 176
: 120
IDX : 176
OFFSET1 : R 30 G 35 B 27
OFFSET1 : R 30 G 35 B 27
LE
LE
SCALER
SCALER
: ADD : 0 VAL : 0 READWRITE
: ADD : 0 VAL : 0 READWRITE
NVRAM
NVRAM
: ADD : 0 VAL : 0 READWRITE
: ADD : 0 VAL : 0 READWRITE
PANEL
PANEL
:
:
1024x768 59.9K @74.8
1024x768 59.9K @74.8
0
9300 K
13. Press
or
buttons to select R G B. Increase/decrease value by
press
or
buttons until the X, Y co-ordinates as below:
x= 0.281
0.005
y= 0.311
0.005
Clear image
button.
255
255
128
128
HS
HS
Hide quick links:
Advertisement
Table of Contents
