Advertisement
Features
• 4 Channel Amplifier with AccuBASS® Processing
• Configurable as 4/3/2 channels
• 4 x 200 W @ 2 ohms, 125 W @ 4 ohms, 2 x 400 W bridged
• High Current Design
• 4 RCA Line Inputs
• 2 RCA Line Outputs
• 6 Summable Speaker-Level Inputs for OEM integration
• MILC
Level Matching Technology (Patent pending)
TM
• GTO
Signal Sense (Great Turn On)
TM
• Independent 12 dB Linkwitz-Riley Crossovers
• Optional ACR-1 Dash Remote
• Solid and Rugged Chassis
• Minty
High-Power Multi-Channel Amplifier
Quick Start Guide
Advertisement
Table of Contents
Related Manuals for AudioControl LC-4.800
Summary of Contents for AudioControl LC-4.800
- Page 1 Features • 4 Channel Amplifier with AccuBASS® Processing • Configurable as 4/3/2 channels • 4 x 200 W @ 2 ohms, 125 W @ 4 ohms, 2 x 400 W bridged • High Current Design • 4 RCA Line Inputs •...
-
Page 2: Important Safety Instructions
Important Safety Instructions 14. This apparatus shall not be exposed to dripping or splashing, and no Read these instructions. object filled with liquids, shall be placed on the apparatus. Keep these instructions. 15. Fuses shall be replaced only with the correct type and fuse value, and Heed all warnings. -
Page 3: Connection Panel Features
12V remote trigger output of some head units. When the head 9. Speaker-Level Output Terminals – These screw terminals unit is turned on, then the LC-4.800 will turn on. connect with speaker wire to your loudspeakers Make sure that 4. -
Page 4: Control Panel Features
Control Panel Features 10 11 12 13 14 15 16 17 18 19 20 14 21 15 16 17 22 23 Quick Start Guide... - Page 5 See specifications page 11 for a list of diagnostic codes. er. So two inputs (L/R) can feed four outputs (2L/2R). 12. GTO Signal Sense – In the ON position, the LC-4.800 amplifier will turn on gracefully when it detects an incoming audio signal, and 21.
-
Page 6: Quick Start
Quick Start Here are a few general steps to get your LC-4.800 amplifier up and 8. Connect the Ground terminal of the unit to the chassis of the running: vehicle, using the same wire gauge as the +12V power wire. -
Page 7: Power Connections
LC-4.800 amplifier. Alternatively, the GTO signal sense feature can be used to gently turn on the LC-4.800 amplifier when an audio input signal is detected. In this case, the connection to the LC-4.800’s remote input terminal is not required. - Page 8 System #1: Using speaker-level inputs Front High Speaker-level output Speaker-level output 80 Hz and above Factory Radio Rear Speaker-level output Front Low Speaker-level output Line-Level Speaker-level output 80 Hz and above ACR-1 Notes: Both crossovers are set to 80 Hz high-pass.
- Page 9 System #2: Using line-level inputs Speaker-level output 30 to 80 Hz and above Left Out 2-Channel Audio Device Right Out Line-level Line Level Speaker-level output 30 to 80 Hz and above ACR-1 Notes: Both crossovers are set to high-pass, and adjusted to suit, depending on if you have a subwoofer or not.
- Page 10 The AudioControl ACR-1 dash control is a remote level for your The top lid must be removed to gain access to the controls, and then LC-4.800 amplifier. It may be mounted under the dash using its own put back on again to protect the controls from dust bunnies.
-
Page 11: Specifications
Specifications All specifications are measured at 14.4 VDC (standard automotive voltage). As technology advances, AudioControl reserves the right to continuously change our specifica- tions, like our Pacific Northwest weather, although we are working on changing that as well. LC-4.800 Multi-Channel Amplifier LC-4.800 Ampli er Codes:... -
Page 12: Block Diagram
Block Diagram Inputs Level Active Speaker Speaker Level Speaker Level Front High Outputs Conversion AccuBASS Mono/ Variable HP Gain & ACR-1 Stereo Crossover Bridged Active Signal Sense Speaker Level Speaker Level Front MILC Conversion Power Amplifiers Line Level Matching 2 x 200 W @ 2 ohm Outputs Left Remote Level...