Maintenance And Service - Bosch PSB 530 RE Original Instructions Manual

OBJ_BUCH-1750-002.book Page 13 Monday, November 4, 2013 3:14 PM
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Reversing the rotational direction (see figures C–D)
The rotational direction switch 5 is used to reverse the rota-
tional direction of the machine. However, this is not possible
with the On/Off switch 4 actuated.
Right Rotation: For drilling and driving in screws, push the
rotational direction switch 5 left to the stop.
Left Rotation: For loosening and unscrewing screws and
nuts, press the rotational direction switch 5 through to the
right stop.
Setting the operating mode
Drilling and Screwdriving
Set the selector switch 2 to the "Drilling" symbol.
Impact Drilling
Set the selector switch 2 to the "Impact drilling"
symbol.
The selector switch 2 engages noticeably and can also be ac-
tuated with the machine running.
Switching On and Off
To start the machine, press the On/Off switch 4 and keep it
pressed.
To lock the pressed On/Off switch 4, press the lock-on button
3.
To switch off the machine, release the On/Off switch 4 or
when it is locked with the lock-on button 3, briefly press the
On/Off switch 4 and then release it.
To save energy, only switch the power tool on when using it.
Adjusting the Speed/Impact Frequency
The speed/impact rate of the switched on power tool can be
variably adjusted, depending on how far the On/Off switch 4
is pressed.
Light pressure on the On/Off switch 4 results in low speed/
impact rate. Further pressure on the switch increases the
speed/impact rate.
Bosch Power Tools
Working Advice
 Apply the power tool to the screw/nut only when it is
switched off. Rotating tool inserts can slip off.
 Do not operate the power tool stationary. It is not de-
signed for operation in a drill stand.
 Before any work on the machine itself, pull the mains
plug.
After longer periods of working at low speed, allow the ma-
chine to cool down by running it for approx. 3 minutes at max-
imum speed with no load.

Maintenance and Service

Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
English | 13
2 609 007 741 | (4.11.13)