Warranty - Virutex FR156N Operating Instructions Manual

Make sure that the collet diameter mat-
ches the shank of the bit to be used.
Never use the machine without fitting
the head first.
8. CHANGE OF THE TRIMMING HEAD BASE
Disconnect the machine from the
power supply before this operation.
The machine is delivered from factory with the
trimming head base d.20 for bits of 3 mm radius. When
working with a bit 6 mm radius it will be necessary
to change this base for the one d.26. If a bit 8 mm
radius is used the standard base must be replaced for
the one d.30. Both extra bases are included as standard
equipment with the machine.
To change base M, first remove the dust collector
connection L, by unscrewing knob N (Fig. 7). Once
connection L has been removed, unfasten screws P to
remove base M and fit the appropriate base for the
bit you are going to use. Next, fit the dust collector
connection L by screwing in knob N.
9. MAINTENANCE. CARBON
BRUSHES AND COMMUTATOR
Disconnect the machine from the
power supply before any maintenance
operation.
Remove screws F (Fig. 5) that fasten the side covers and
detach both. Remove the brush-holder I (Fig. 6) with
small screwdriver H, using one of the brush-holder side
tabs to lever it out. Push back the end of spring J. Keep
it in this position to extract the brush and replace it
with a new genuine VIRUTEX brush. Reinsert the brush-
holder, ensuring that it is firmly positioned in the casing
and that each of the brushes exerts a small amount of
pressure on the collector. Re-attach the covers G with
the corresponding screws, making sure that no wires
get caught in the process. Mount the springs and cap
as already indicated above. It is advisable to run the
machine for 15 minutes after changing the brushes.
Should the commutator show burnings or scratches it
is better to resurface it on a lathe at a VIRUTEX service.
Never use abrasive paper to do so. Keep the cable and
socket in good condition.
10. OPTIONAL ACCESSORIES
1140123 2 mm radius bit with bearings. H.M.
1140106 3 mm radius bit with bearings. H.M.
1140109 6 mm radius bit with bearings. H.M.
1140110 8 mm radius bit with bearings. H.M.
1222084 Ø 6 mm collet
1222024 Ø 8 mm collet
1222085 Ø 6.35 mm (1/4") collet
5600050 CA56G head
Gives you a large support surface on the piece when
routing both horizontal edges and straight, rounded or
shaped parts, resulting in excellent stability, precision
and comfort when shaping (Fig. 9).
The CA56G Head is mounted and adjusted in the same
way as the router header for the FR156N Router, as
shown in this manual.
6446073 Standard dust collector attachment 3.5 m
11. NOISE LEVEL
These levels have been measured according to the
European Standard EN50144.
Noise level at work area can exceed 85 dB (A). In that
case operators should protect themselves against da-
mage to hearing.

12. WARRANTY

All VIRUTEX power tools are guaranteed for 12 months
fromthe date of purchase, excluding any damage which
is a result of incorrect use or of natural wear and tear
on the machine. All repairs should be carried out by the
official VIRUTEX technical assistance service.
VIRUTEX reserves the right to modify its products
without prior notice.
F R A N Ç A I S
AFFLEUREUSE FR156N
Important
Avant d'utiliser la machine, lisez attenti-
vement ce MANUEL D'INSTRUCTIONS et la
BROCHURE D'INSTRUCTIONS GÉNÉRALES
DE SÉCURITÉ qui vous sont fournis avec
cette machine. Assurez-vous de bien
avoir tout compris avant de commencer
à travailler sur la machine.
Gardez toujours ces deux manuels
d'instructions à portée de la main pour
pouvoir les consulter, en cas de besoin.
7