Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt D28114N-XE
Summary of Contents for DeWalt D28114N-XE
- Page 1 INSTRUCTION MANUAL D28114N-XE HEAVY-DUTY SMALL ANGLE GRINDER...
-
Page 3: Definitions: Safety Guidelines
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing D28114N-XE the job. This may significantly reduce the exposure level over the total working period. - Page 4 GENERAL POWER TOOL SAFETY WARNINGS 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when WARNING! Read all safety warnings and all instructions Failure to follow operating a power tool. Do not use a power tool while you are tired or the warnings and instructions may result in electric shock, fire and/or serious under the influence of drugs, alcohol or medication.
-
Page 5: Extension Cords
d) Store idle power tools out of the reach of children and do not allow means your tool will operate on alternating current. Operation at a voltage outside this range can cause loss of power and can result in overheating. All D WALT tools are persons unfamiliar with the power tool or these instructions to operate the factory tested;... -
Page 6: Further Safety Instructions For All Operations
e) The arbour size of wheels, flanges, backing pads or any other accessory must m) Regularly clean the power tool’s air vents. The motor’s fan will draw the dust properly fit the spindle of the power tool. Accessories with arbour holes that inside the housing and excessive accumulation of powdered metal may cause do not match the mounting hardware of the power tool will run out of balance, electrical hazards. - Page 7 e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such the wheel is in motion otherwise kickback may occur. Investigate and take blades create frequent kickback and loss of control. corrective action to eliminate the cause of wheel binding. d) Do not restart the cutting operation in the workpiece.
-
Page 8: Package Contents
exposed areas with soap and water. Allowing dust to get into your mouth, eyes, WARNING: The grinding wheel or accessory may loosen during coast-down of or lay on the skin may promote absorption of harmful chemicals. the tool when shut off if rubber ring is missing or damaged. If grinding wheel or accessory loosens, it may dismount from the machine and may cause serious WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. - Page 9 INTENDED USE • Check for damage to the tool, parts or accessories which may have The D28114N-XE heavy-duty small angle grinder has been designed for professional occurred during transport. grinding, polishing and cutting applications. • Take the time to thoroughly read and understand this manual prior to DO NOT use grinding wheels other than center depressed wheels and flap-disk.
- Page 10 Attaching Side Handle accessories. Before reconnecting the tool, depress and release the paddle switch to FIG. 2 ensure that the tool is off. An accidental start-up can cause injury. The side handle (D) can be fitted to either side of the gear case CAUTION: Guards must be used with all grinding wheels, sanding flap discs, wire in the threaded holes, as shown.
- Page 11 115 mm and 125 mm (4-1/2" and 5") Grinding Wheels 115 mm and 125 mm (4-1/2" and 5") Cutting Wheels Type 27 guard Type 1 guard Type 1 guard Type 27 guard Quick-change Quick-change Quick-change backing flange backing flange backing flange Type 27 hubbed wheel Type 1 abrasive Diamond cutting wheel...
-
Page 12: Operation
FIG. 5 115 mm and 125 mm (4-1/2" and 5") Sanding Flap Discs NOTE: The guard is pre-adjusted to the diameter of the gear case hub at the factory. If, after a period of time, the guard becomes loose, tighten the adjusting screw (M) with clamp lever in the closed position. - Page 13 Switches lock while the tool is operating because damage to the tool will result. To engage the lock, depress the spindle lock button (B) and rotate the spindle (P) until you are CAUTION: Hold the side handle and body of the tool firmly to maintain control of unable to rotate the spindle further.
- Page 14 3. While depressing the spindle lock button, thread the EDGE GRINDING WITH GRINDING WHEELS FIG. 12 FIG. 10 clamp nut (G) on spindle. If the wheel you are 6.35 mm WHEELS CAUTION: Wheels used for cutting and edge grinding (1/4") installing is more than 3.17 mm (1/8") thick, place may break if they bend or twist while the tool is being used the threaded clamp nut on the spindle so that the...
- Page 15 5. Remove the tool from work surface before turning tool off. Allow the tool to stop 3. Maintain a 5˚ to 15˚ angle between the tool and FIG. 15 rotating before laying it down. work surface. The san ding disc should contact approximately one inch of work surface.
- Page 16 1. Allow the tool to reach full speed before touching the tool to the work surface. MOUNTING CLOSED (TYPE 1) GUARD FIG. 18 1. Open the guard latch (J). Align the 2. Apply minimum pressure to work surface, allowing the tool to operate at high lugs (K) on the guard with the slots (L) speed.
-
Page 17: Maintenance
Cleaning 2. Place the wheel on the backing flange, centering the wheel on the raised section (pilot). WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once 3. Install the threaded clamp nut with the raised section (pilot) facing away from the a week. - Page 20 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 444 224 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (JAN13) Part No. N254142 D28114N-XE Copyright © 2012, 2013 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...