Specifications - Bosch GOP Professional 300 SCE Original Instructions Manual

OBJ_BUCH-1271-003.book Page 14 Monday, July 11, 2011 10:01 AM
14 | English
Wear protective gloves when changing application
tools/accessories. Application tools/accessories become
hot after prolonged usage.
Do not scrape wetted materials (e.g. wallpaper) or on
moist surfaces. Penetration of water into the machine in-
creases the risk of an electric shock.
Do not treat the surface to be worked with solvent-con-
taining fluids. Materials being warmed up by the scraping
can cause toxic vapours to develop.
Exercise extreme caution when handling the scraper.
The accessory is very sharp; danger of injury.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
Product Description and

Specifications

Read all safety warnings and all instruc-
tions. Failure to follow the warnings and
instructions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Technical Data
Multi-Cutter
Article number
Preselection of orbital stroke rate
Rated power input
Output power
No-load speed n
0
Oscillation angle, left/right
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
2 609 932 802 | (11.7.11)
Intended Use
The machine is intended for sawing and cutting wooden mate-
rials, plastic, gypsum, non-ferrous metals and fastening ele-
ments (e.g., unhardened nails, staples). It is also suitable for
working soft wall tiles, as well as for dry sanding and scraping
of small surfaces. It is especially suitable for working close to
edges and for flush cutting. Operate the power tool exclusive-
ly with Bosch accessories.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Thumbwheel for orbit frequency preselection
3 Venting slots
4 Tool holder
5 Handle (insulated gripping surface)
6 Plunge saw blade*
7 Clamping bolt with spring washer (GOP 250 CE)
8 Allen key
9 Adapter for tool holder (GOP 250 CE)
10 Sanding plate*
11 Sanding sheet*
12 SDS lever for releasing the application tool
(GOP 300 SCE)
13 Adapter for SDS tool holder (GOP 300 SCE)
14 Clamping bolt for tool adapter (GOP 300 SCE)
15 Felt ring of the dust extraction*
16 Retaining clip of the dust extraction*
17 Vacuum connection*
18 Dust extraction*
19 Vacuum hose*
20 Extraction adapter*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GOP 250 CE
Professional
3 601 B30 0..
W 250
W 150
-1
min 8000–20000
° 1.4
kg 1.5
/II
GOP 300 SCE
Professional
3 601 B30 5..
300
180
8000–20000
1.4
1.6
/II
Bosch Power Tools