Advertisement
3. How to Assemble
IMPORTANT: Always unplug the vacuum
cleaner from the electrical outlet before
assembling or removing the accessories.
Insert the flexible hose (Fig.3/1) into the inlet
on the main body by pressing the clip on the
connector and releasing when the clip clicks
into place.
Fig.3/1
Push the telescopic extension tube on to the
end of the handle (Fig.3/2).
Fig.3/2
The telescopic tube can be lengthened or
shortened by pushing the button in and
sliding the tube apart or together as required.
(Fig.3/3).
Fig.3/3
Fit the combination floor head by pushing
onto the extension tube. (Fig.3/4).
Fig.3/4
4
4. How to Operate
Cord Release
Fully unwind the power cord. A yellow mark on
the power cord indicates the recommended
cord length. Do not unwind the cord beyond
this mark.
On/off Button
1. Insert the plug into the electrical outlet.
2. Press the on/off switch located on the
top of the vacuum cleaner, to switch on
the vacuum cleaner and press the button
again to turn the vacuum cleaner off.
Carpet Cleaning
For carpet and rug cleaning, press the rocker
switch on the combination floor head to raise
the brushes.
Hard Floor Cleaning
For hard floor cleaning, press the rocker
switch on the combination floor head to lower
the brushes.
Cord Rewind
To rewind the power cord, press the cord
rewind button located on the top of the
vacuum cleaner, and guide the power cord
with one hand. Rewind 1-1
/
metres of cord
1
2
at a time. This will prevent the cord from
whipping which could cause damage or
injury.
Carry Handle
Use the carry handle located at the top of the
dirt bin to move from room to room.
Hose Storage
For convenience there is a parking slot located
at the rear of the vacuum cleaner where the
floor tool and hose can be parked for carrying
and storage.
5. Accessories
1. The accessories can be attached directly
to the handle by removing the telescopic
tubes
and
pushing
in
the
desired
accessory.
2. The accessories can also be attached to
the telescopic extension tube for extra
reach. Remove the combination floor head
and push on the desired accessory.
2-in1 tool:
Dusting brush: for delicate surfaces
Upholstery tool: for carpet, upholstery and
stairs etc.
Crevice tool: for crevices, corners and
cracks, etc.
6. Dirt Container & Filters
Removal & Replacement
IMPORTANT: Always unplug the vacuum
cleaner from the electrical outlet before
removing the dirt container.
IMPORTANT: Do NOT use the vacuum
cleaner without ALL of the filters in place.
Emptying the dirt container
Press the dirt bin release button on the main
body of the unit. The dust container can then
be lifted and removed off the unit. (Fig.6/1)
Hold the dirt container
over a bin and press
the quick release
button as shown
(Fig.6/2).
When all the dirt has
fallen, close the dirt
container flap, a click
will be heard when
closed. Then return the dirt container to the
unit which will click into place when secure.
Cleaning the cyclone separator
1. Remove the dirt container from the unit as
directed above and dispose of dirt inside
the container before cleaning.
2. Rotate the lid of the dirt container anti-
clockwise to remove the dirt container off
the cyclonic separator (Fig 6/3).
Fig.6/3
The separator should be cleaned with a soft
brush and wiped with a damp cloth. The dirt
container can be wiped clean (Fig 6/4).
Fig.6/4
IMPORTANT: The cyclonic separator
should not be submerged in water.
When the cyclone separator has been
cleaned, leave the separator to dry completely.
Re-attach the dirt container to the lid of the
separator and return the dirt container to the
unit.
Cleaning the Pre-motor filter
NOTE: This is located on the rear of the unit,
underneath the pedals.
Release the pre-motor filter cover by sliding
across the release catch to the right. Lift off
the filter cover to gain access to the filter.
Remove the filter by pulling the tab towards
you (Fig 6/5).
5
Advertisement
