Charging Procedure - Black & Decker BDCDE120 Instruction Manual

short circuit. NOTE: Lithium-Ion batteries
should n ot b eputin
checked baggage.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is
cool and dry away from direct sunlight and
excess heat or cold.
2. Long storage will not harm the battery
pack or charger.
CHARGING PROCEDURE
Black+Decker chargers are designed to
charge Black+Decker battery packs in
3-4 hours depending on the pack being
charged.
1. Plug the charger into an appropriate outlet
before inserting the battery pack.
2. Insert the battery pack into the charger
as shown in figure A.
J
i ! ¸
/
3. The green LED will flash indicating that
the battery is being charged.
4. The completion of charge is indicated by
the green LED remaining on continuously.
The pack is fully charged and may be used
at this time or left on the charger.
Recharge discharged batteries as soon
as possible after use or battery life may
diminished. For longest battery
life, do not discharae batteries fully.
It is recommended tfiat the batteries 6e
recharged after each use.
LEAVING THE BATTERY IN THE
CHARGER
The charger and battery pack can be left
connected with the green LED glowing
indefinitely. The charger will keep thebattery
pack fresh and fully charged.
iMPORTANT CHARGING NOTES
1. Longest life and best performance can
be obtained if the battery pack is charged
when the air toemperature is between 65°F
and 75 F (18 - 24 C). DO NOT charge the
battery pack in an air temperature below
+40°F (+4.5°C), or above +105°F (+40.5°C).
This is _mportant and will prevent serious
damage to the battery pack.
2. The charger and battery pack may
become warm to touch while charging.
This is a normal condition, and does not
indicate a problem. To facilitate the cooling
of the battery pack after use, avoid placing
the charger or battery, pack in a warm
environment such as tn a metal shed, or an
uninsulated trailer.
3. If the battery pack does not charge
properly:
a. Check current at receptacle by plugging
in a lamp or other appliance
b. Check to see if receptacle is connected to
a light switch which turns power off when you
turn out the lights.
c. Move charger and battery pack to a
location where the surrounding air
temperature is approximately 65°F - 75°F
(18 °- 24°C).
d. If charging problems persist, take the
tool, battery pack and charger to your
local service center.
4. The battery pack should be recharged
when it fails to produce sufficient power on
j_bs which were easily done previously.
O NOT CONTINUE to use under these
conditions. Follow the charging procedure.
You may also charge a partially used pack
whenever you desire with no adverse affect
on the battery pack.
5. Foreign materials of a conductive nature
such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic
particles should be kept away from charger
cavities. Always unplug the charger from
the power supply when there is no battery
pack in the cavity. Unplug charger before
attempting to clean.
6. Do not freeze or immerse charger in
water or any other liquid.
zLWARNING:
Shock hazard. Do not
allow any liquid to get inside charger. Never
attempt to open the battery pack for any
reason. If the plastic housing of the battery
pack breaks or cracks, return to a service
center for recycling.
SAFETY WARNINGS AND
INSTRUCTIONS: DRILLS
1.Hold drill firmly with one hand on the grip
and the other hand on the bottom of the
battery pack.
2. When attaching accessories in the drill
chuck, hand tighten the keyless chuck
firmly.
zLWARNING:
Drill may stall (if overloaded
or improperly used) causing a twist. Always
expect the stall. Grip the drill firmly with both
hands to control the twisting action and
prevent loss of control which could cause
personal injury. If a stall does occur, release
the trigger immediately and determine the
reason for the stall before re-starting.
INSTALLING AND REMOVING
THE BATTERY PACK FROM
THE TOOL
AWARNING:
Make certain the lock-off
button is engaged to prevent switch
actuation before removing or instafling
battery.
TO INSTALL BATTERY PACK: Insert
battery (5) into tool until an audible click is
6