Table of Contents
Advertisement
Quick Links
Operator's
Manual
U.S. Patent No. 6,760,947; No. 6,105,192; No. 6,493,896 (Deluxe Machines)
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read this book
prior to operating or attempting any service or maintenance procedure to your ALTO machine could result
in injury to you or to other personnel; damage to the machine or to other property could occur as well. You
must have training in the operation of this machine before using it. If your operator(s) cannot read this
manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: ALTO, 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 70935A 9/05
CLARKE TECHNOLOGY
SCRUBTEC 770 S
SCRUBTEC 770 S
SCRUBTEC 770 S
SCRUBTEC 770 S
SCRUBTEC 770 S
SCRUBTEC 770 L
SCRUBTEC 770 L
SCRUBTEC 770 L
SCRUBTEC 770 L
SCRUBTEC 770 L
SCRUBTEC 784 S
SCRUBTEC 784 S
SCRUBTEC 784 S
SCRUBTEC 784 S
SCRUBTEC 784 S
SCRUBTEC 784 L
SCRUBTEC 784 L
SCRUBTEC 784 L
SCRUBTEC 784 L
SCRUBTEC 784 L
SCRUBTEC 795 S
SCRUBTEC 795 S
SCRUBTEC 795 S
SCRUBTEC 795 S
SCRUBTEC 795 S
SCRUBTEC 795 L
SCRUBTEC 795 L
SCRUBTEC 795 L
SCRUBTEC 795 L
SCRUBTEC 795 L
Printed in the U.S.A.
Advertisement
Table of Contents
Related Manuals for Alto SCRUBTEC 770 L
Summary of Contents for Alto SCRUBTEC 770 L
- Page 1 Form No. 70935A 9/05 SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 784 S SCRUBTEC 784 S...
-
Page 2: Table Of Contents
How To Clean A Floor ... 22 Maintenance ... 23 How To Correct A Problem ... 28 Common Error Codes (SRUBTEC 770 L, 784 L & 795 L) ... 29 Accessories ... 30 Section II Parts and Service Manual Solution Tank Assembly ... 32 Parts List ... -
Page 3: Operator Safety Instructions
OPERATOR SAFETY INSTRUCTIONS DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel;... -
Page 4: Introduction
WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other bystanders. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities. WARNING: Electrical components of this machine can "short-out" if exposed to water or moisture. Keep the electrical components of the machine dry. -
Page 5: Machine Specifications
Machine Specifications SPECIFICATIONS: Model Scrubtec 795 S Motor, Vac 1 HP (.74kw) three stage tangential discharge Power Supply 36 volt (6-6V batteries) 250AH, 330AH Solution Tank 30 gallon (114 liter) Recovery Tank 30 gallon (114 liter) Motors, Brush (2) 1 hp PM (.74kw) Motor Traction .50 hp PM (.37kw) Brushes (2) - Page 6 1015 lbs. 460kg 1318 lbs. 598kg <70 dBA <2.5 m/s Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY Scrubtec 770 L 1HP (.74kw) three stage tagential discharge 36 volt (6-6V batteries) 250AH, 330AH 30 gallon (114 liter) 30 gallon (114 liter) 1 hp PM (.74kw)
-
Page 7: Procedures For Transporting
PROCEDURES FOR TRANSPORTING How To Put The Machine In A Van Or Truck WARNING: The machine is heavy. Make sure you use two able persons to assist the machine in climbing the ramp. 1. Make sure the loading ramp is at least 2.4m long, and strong enough to support the machine. 2. -
Page 8: Symbols Used On S & L Models
Charge/Battery Solution Control Meter Page SYMBOLS USED ON On/Off Key Switch Power SCRUBTEC 770 L, 784 L & 795 L Squeegee Up/Down Brush Up/Down Charge Indicator Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY Traverse Speed Control... - Page 9 SYMBOLS USED ON SCRUBTEC 770, 784, 795 71018A WARNING MOVING PARTS. CONTACT CAN CAUSE SEVERE INJURY. • Do not place hands or feet under machine when in 71017A use. CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 WARNING READ OPERATOR'S MANUAL BEFORE...
-
Page 10: Machine Control Panel S Models
MACHINE CONTROL PANEL SRUBTEC 770 S, 784 S & 795 S Key Switch (See Figure #1, Item "A") The key switch turns "ON" the power to the control panel. "0" is "OFF" and "I" is "ON". Traverse Speed Switch (See Figure #1, Item "B") The speed control varies from low to high speed. - Page 11 MACHINE CONTROL PANEL SRUBTEC 770 S, 784 S & 795 S CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 Figure #1 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 - 11 -...
-
Page 12: Machine Control Panel L Models
MACHINE CONTROL PANEL SRUBTEC 770 L, 784 L & 795 L Key Switch (See Figure #2 Item "A") The key switch turns "ON" the power to the control panel. "O" is "OFF" and "I" is "ON". Traverse Speed Switch (See Figure #2, Item "B") The speed control varies from low to high speed. - Page 13 MACHINE CONTROL PANEL SRUBTEC 770 L, 784 L & 795 L Circuit Breakers (See Figure #2, Item "K", "L", "M") The circuit breaker reset buttons are located on the control panel. The breakers are located as follows: "M" - Brush Motors (35A); Item N - Key Switch (5A).
-
Page 14: Display Screen For L Models
Display Screens For SCRUBTEC 770 L, 784 L, 795 L SCREEN 1 “Battery” blinks when low voltage occurs. Screens Available to Operator SCREEN 2 Example The Diagnostic only. It will not show unless a fault with the machine occurs. When the fault happens the icon and error code will be displayed. -
Page 15: Machine Controls And Features
MACHINE CONTROLS & FEATURES Squeegee Lift Handle ("S Class" models only) See Figure #3a, 3b, & 3c. The squeegee lift handle is located below the control handles on the right side. It is used to raise or lower the squeegee. The vac motor is turned on when the handle is lowered. -
Page 16: How To Prepare The Machine For Operation
HOW TO PREPARE THE MACHINE FOR OPERATION How To Install The Batteries The Scrubtec machines use six 6-volt batteries. The batteries are located in the battery compartment under the recovery tank. To Install the batteries, follow this procedure: 1. Turn key switch off. 2. -
Page 17: Battery Maintenance
HOW TO PREPARE THE MACHINE FOR OPERATION Battery Maintenance The electrical power to operate the machine comes from the storage batteries. Storage batteries need preventive main- tenance. WARNING: Working with batteries can be dan- gerous. Always wear eye protec- tion and protective clothing when working near batteries. -
Page 18: How To Charge The Batteries
HOW TO PREPARE THE MACHINE FOR OPERATION How To Charge The Batteries WARNING: Charging the batteries in an area without adequate ventilation could result in an explosion. To prevent an explosion, charge the batteries only in an area with good ventilation. WARNING: Lead acid batteries generate gases which could explode. -
Page 19: How To Install The Brushes Or Pad Drivers
HOW TO PREPARE THE MACHINE FOR OPERATION How To Install The Brushes Or Pad Drivers To install the brushes or pad drivers on the machine, follow this procedure: 1. Turn the key switch "ON". 2. Put the brush switch in the "UP" position. 3. -
Page 20: How To Operate The Machine
HOW TO OPERATE THE MACHINE How to Operate the One Touch System ("L Class" models only) One touch cleaning is a feature on the new Scrubtec Walk-behind Scrubber. The factory defaults for this setting are two bars of brush pressure and four bars for solution flow and squeegee in the down position. -
Page 21: How To Operate The Squeegee
HOW TO OPERATE THE MACHINE How To Operate the Squeegee ("S Class" models only) The squeegee wipes the floor while the vacuum motor removes the dirty solution from the floor. Use your right hand to lower or raise the squeegee handle. To operate the squeegee, follow this procedure: 1. -
Page 22: How To Traverse Machine
HOW TO OPERATE THE MACHINE How To Traverse Machine NOTE: Put the machine in the slow traverse speed (see figure #17). Use the machine in an area that has no furniture and objects until you can do the following: 1. Move the machine in a straight direction, forward and backward. -
Page 23: Maintenance
HOW TO OPERATE THE MACHINE How to Clean a Very Dirty Floor To clean a very dirty floor, follow this procedure: 1. Apply solution to the floor. 2. Do not lower the squeegee. 3. Do not activate the vacuum motor. 4. - Page 24 MAINTENANCE Do These Procedures When You End Your Work 1. Drain the solution tank (Figure #21, item A) and the recovery tank (Figure #21, item B). To drain the tanks , follow this procedure: a. Turn the key switch “OFF”. b.
- Page 25 MAINTENANCE These Maintenance Procedures Must Be Done Every Week: WARNING: Maintenance and repairs must be done by authorized personnel only. Always empty the solution tank and the recovery tank before doing any maintenance. Keep all fasteners tight. WARNING: Always wear eye protection and pro- tective clothing when working near batteries.
- Page 26 MAINTENANCE 7. Check the squeegee and the scrub brushes or the pad drivers for damage. 8. Check the squeegee and the vacuum hose for dam age, leaks and obstructions. Maintenance For The Squeegee To remove the squeegee, follow this procedure: 1.
- Page 27 MAINTENANCE Adjusting Squeegee Blades When properly installed the front blade should be ap- proximately .06 above the rear blade. See figure #29. Adjusting Squeegee Support Wheels: The support wheels should be set at .12 above the floor with the rear blade touching the floor. See figure #31. WARNING: Maintenance and repairs must be done by author-...
-
Page 28: How To Correct Problems In The Machine
HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM The machine does not remove all the water from the floor. The batteries do not give the normal running time. The cleaning is not even. The machine does not run. Page -28- CAUSE The squeegee is up The vacuum tank is full. -
Page 29: Common Error Codes (Srubtec 770 L, 784 L & 795 L)
SCRUBTEC 770 L, 784 L, 795 L ERROR CODE 3100 Probable short circuit of 3101 output device. 3102 3103 3104 3105 7600 Open circuit on brush motors or brush motor wiring. 7603 Possible short circuit on brush motors or wiring. -
Page 30: Accessories
CCESSORIES Description Power Wand System Kit ESP Recycle System Kit Soft Caster Asm. Care Kit Squeegee Asm., Optional 74 cm (770 model only) Drive Wheel, Foam Filled Imperial Electric Parking Brake Kit Battery Maintenance System Machine Blade Type Inner Optional Inner Optional Inner... -
Page 31: Section Ii Parts And Service Manual
CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 784 S... -
Page 32: Solution Tank Assembly
33 34 Page -32- CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 Solution Tank Assembly Drawing 9/05 Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY To Electrical Panel... -
Page 33: Parts List
Solution Tank Assembly Parts List 9/05 Ref # Part No. Description 881317 891384 842406 842406 40860A 40613A 40612A 61713A 170892 170915 962027 50966A 30590E 60480A 80108A 30598A 51346A 872010 98465A 980657 962139 61590A 59614A 53571A 30453A 822802 30445A 50358A 838517 830214 50359A 53568A... -
Page 34: Recovery Tank Assembly
Recovery Tank Assembly Drawing 2/05 Page -34- CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795... -
Page 35: Parts List
Recovery Tank Support Washer, Nylon Shoulder Screw Hinge Pin (included with item #36) Tank, Recovery, 770 S Tank, Recovery, 770 L Tank, Recovery, 784 S Tank, Recovery, 784 L Tank, Recovery, 795 S Tank, Recovery, 795 L Float Switch (includes items, #38 & 2 ea. #11& #12) -
Page 36: Electrical Panel Assembly S Models
Page -36- CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S Electrical Panel Assembly Drawing 9/05 Drawing # 10849E... -
Page 37: Parts List
Electrical Panel Assembly Parts List 9/05 Ref # Part No. Description 962980 962139 85391A 30594A 81104A 87007A 980651 80030A 980614 902731 920110 53569A 80285A 83302A 854849 170781 193951 83307A 61589A 54764A 54763A 40736A 40125A 41801A 41802A 61682A 40735A 40759A 80254A 962666 912287 920296... -
Page 38: Electrical Panel Assembly L Models
Page -38- CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L... -
Page 39: Parts List
CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L... -
Page 40: Control Panel Assembly
Page -40- CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 Control Panel Assembly Drawing 9/05 Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795... -
Page 41: Parts List
Control Panel Assembly Parts List 9/05 Ref. # Part No. 30592A 85815A 980205 85813A 920110 52556A 40750A 40738A 50962A 962262 30055A 30056A 50961A 80104A 40126A 980608 962330 40786R 40786A 40786S 40748A 40880A 40758A 40168B 40747A 962957 70962A 34264A 61597A 41431B 41423B 85391A 980614... -
Page 42: Squeegee Swing Arm Assembly
Squeegee Swing Arm Assembly Drawing 2/05 Page -42- CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY NOTE:... -
Page 43: Parts List
Squeegee Swing Arm Assembly Parts List 2/05 Ref # Part No. Description 57275A Pulley 87623A Washer, Nylon 1¼x¼x 60452A Swing Arm, Front 86004A Screw, .25-20 x 1½ 85730A Screw, .375-16 x 1¼ 81104A Nut, Hex ESNA SS 38021A Strap 61679A Cable, Lower 51613A Bumper... -
Page 44: Traverse System Assembly
Page -44- CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 Traverse System Assembly Drawing 2/05 Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795... -
Page 45: Parts List
Traverse System Assembly Parts List 2/05 Ref # Part No. Description 66531A 836711 81104A 69877A 85811A 57275A 87623A 86004A 962288 85700A 920110 899769 81105A 59116E 85730A 59969A 59955A 81221A 980614 61594A 65963A 87625A 80011A 81207A 170883 58419A 980205 69639A 980645 962244 980638 32417B... -
Page 46: Brush Head Assembly
Page -46- CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 Brush Head Assembly Drawing 2/05 Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795... -
Page 47: Parts List
Ref # Part No. Description 82501A 766780 Hair Pin 38723A Nylon Spacer 52497A Actuator & Tube Asm. 52499A Actuator & Tube Asm. 980673 Washer 920278 Nut, Jam 50-20 980626 Washer, Lock .50 67705B Sleeve Bearing 63032A Linkage Bar 85838A Screw, .50-201.50 41601A Connector 41602A... -
Page 48: Brush Motor
Seam Location Page -48- CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 Brush Motor #45036A 2/05 Ref # Part No. -
Page 49: Gearbox
Ref # CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 Gear Box #54238A 2/05 Part No. -
Page 50: Vac Motor
Ref # Part No. Description 51913A Clip (optional) 54809A Housing 53905A 85303A Screw - 8-32 x 40830A Carbon Brushes 51914A Clamp 50618A Bracket 53100A Disc 902679 Bearing - Ball 902648 Bearing - ball, radial Page -50- CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795... -
Page 51: Imperial Transaxle Parts 2/05
CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 Imperial Transaxle Parts 2/05 PN 59116A SCRUBTEC 770 / 784 / 795... -
Page 52: Control Panel Connection Diagram S Models
(Front of Machine) Connection Diagram 2/05 Page -52- CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S Control Panel Connection Diagram 2/05 CLARKE TECHNOLOGY... -
Page 53: Control Panel Connection Diagram L Models
CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L... -
Page 54: Electrical Plate Connection Diagram S Models
Electrical Plate Connection Diagram 9/05 Page -54- CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY... -
Page 55: Electrical Plate Connection Diagram L Models
CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L... -
Page 56: Control Housing Connection Diagram 2/05
Page -56- CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L... -
Page 57: Electrical Schematic S Models
CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S SCRUBTEC 770 S / 784 S / 795 S Electrical Schematic 9/05... -
Page 58: Electrical Schematic (Top) L Models
Page -58- CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L... -
Page 59: Electrical Schematic (Bottom) L Models
CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L SCRUBTEC 770 L / 784 L / 795 L... - Page 60 CORPO HEADQUARTERS HEADQUARTERS HEADQUARTERS HEADQUARTERS HEADQUARTERS DENMARK DENMARK DENMARK DENMARK DENMARK Nilfisk-Advance Group Sognevej 25 2605 Brøndby Denmark Tel: (+45) 43 23 81 00 SUBSIDIARIES SUBSIDIARIES SUBSIDIARIES SUBSIDIARIES SUBSIDIARIES AUSTRALIA AUSTRALIA AUSTRALIA AUSTRALIA AUSTRALIA ALTO 48 Egerton St. PO Box 6046 Silverwater NSW 2128 Australia Tel: (+61) 2 8748 5966...
-
Page 61: Great Britain
GREAT BRITAIN GREAT BRITAIN GREAT BRITAIN GREAT BRITAIN GREAT BRITAIN ALTO Division of Nilfisk-Advance Ltd. Bowerbank Way Gilwilly Industrial Estate Penrith Cumbria CA 11 9BQ Great Britain Tel: (+44) 1 768 86 89 95 Fax: (+44) 1 768 86 47 13 E-mail: sales@-alto.co.uk www.-alto.co.uk HUNGARY... - Page 62 CLARKE TECHNOLOGY LIMITED U.S. WARRANTY This Clarke Technology Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service, when operated and maintained in accordance with Clarke Technology's Maintenance and Operations instructions. The warranty period is subject to the conditions stated below. 3 YEARS FOR PARTS AND 1 YEAR FOR SERVICE LABOR (See exceptions below) Motors must be inspected for carbon motor brush wear at six-month intervals by an authorized Clarke Technology repair station.
Need help?
Do you have a question about the SCRUBTEC 770 L and is the answer not in the manual?
Questions and answers