Yamaha DVR-S100 Service Manual page 36

DVR-S100/NX-SW100
8. Error Code
Description of error
L. H error
U11 Focus error
H01 Tray loading error
H02 Spindle servo error
H03 Traverse servo error
H04 Tracking servo error
H05 Seek error
H06 Power supply error
DSC related error
F500 DSC error
F501 DSC not ready
F502 DSC time out error
F503 DSC communication failure
F505 DSC Attention Error
F506 Invalid media
ODC related error
No control data is obtainable due to a
F600
demodulation error
F601 Undefined sector ID is requested.
LEAD-IN is not obtainable due to
F602
demodulation error.
F603 KEY DET is not obtainable due to a
demodulation error
F610 ODC abnormal
F611 6626 QCODE don't read Error
F612 No CRC OK is issued for a certain time.
No response is provided for the inquiry of
F630
KEY DET.
CPPM KEY DET is not usable until the
F631
end of the file.
F632 CPPM-KEY-DET is not usable.
Disc code
F103 Illegal highlight position
IIC error
F4FF Forcible initialization failure (time-out)
Microprocessor error
F700 MBX overflow
F701 Message command does not end.
F702 Message command is changed.
F880 Incorrect task number
Message transmission is attempted while
F890
transmitting to AV task
F891 A message cannot be transmitted to AV
task.
F893 FROM is falsified.
F894 EEPROM abnormal
F8A0 Message command is not correct.
OPU : Optical Pick Up, DSC : Digital Servo Controller, FEP : Front End Processor, ODC : Optical Disc Controller, FROM : Flash ROM
36
Supplementary explanation
( Spindle servo, DSC SP motor, CLV servo error)
The power cannot be turned off due to a communication error
between the panel control and the system control.
DSC is stopped due to occurrence of a servo error.
(startup, focus error, etc.)
Communication error between DSC and system control
(communication failure due to DSC not at work)
To be handled in the same way as F500
Communication error (A communication command was
transmitted but an error occurred.)
To be handled in the same way as F500
The disc is upside down, TOC cannot be read, unusable disc Disc
Operation is stopped because the navigation data cannot be
obtained due to a faulty condition of the demodulation system ODC
Operation is stopped due to a request for access by an
abnormal ID data.
LEAD IN data cannot be read.
The CSS data of the disc cannot be obtained.
Issuing a command is not permitted.
No seek address is obtainable in the CD system.
No ID data is obtainable in the DVD system.
(Only when used internally)
The CPPM file system cannot be read due to a scratch, etc.
CPPM-KEY-DET is revoked or falsified.
It is highly possible that disc code is violated when displaying
the highlight.
When sending a message back to Disc Manager
Next message was issued before replying to Disc Manager.
The message is changed before replying to Disc Manager.
When a message comes from non-existing task (error stop,
firm bug correction required)
A message is being transmitted to AV task (error stop, firm
bug correction, etc.)
Transmission of a message to AV task is started. (error stop,
firm bug correction required)
Transmission of a message to AV task is started. (error stop,
firm bug correction required)
Faulty point 1 Faulty point 2 Faulty point 3 Faulty point 4
OPU ADSC FEP
ADSC CPU
OPU ADSC FEP
ADSC FEP EEPROM
OPU ADSC FEP
FEP ADSC
FEP ADSC
ODC FEP ADSC
ODC
ODC
ODC
Disc CPPM
Disc EEPROM CPPM
Disc
EEPROM CPU FEP
Firm bug
Firm bug
Firm bug
Firm bug
Firm bug
Firm bug
FROM CPU
Serial
EEPROM
communication
line
Firm bug
Servo drive
Servo drive
Servo drive
ODC
ADSC