Finding The Handset - Uniden DECT1363 series User Manual

To...
open the lists
scroll through the list
dial the current entry
add 1 at the front of CID number
store the current CID or redial entry to the
phonebook
edit the current phonebook entry
delete the current entry
close the list
When it's in standby, the handset shows how many calls came in since the last time you checked the CID list.
#
Adding Phonebook Entries
With the phone in standby, open the phonebook. Press
and number.
x Enter the phone number (up to 20 digits) exactly as you would dial it.
x If you need to enter a pause between the numbers, press
about 2 seconds per a digit.)
x To edit the number, press
Deleting All the Phonebook Entries / CID Records
With the phone in standby, open the phonebook or CID list. Press
Chain Dialing
If you often have to enter a series of digits or a code number during a call, you can save that code number as a regular phonebook
entry and use the phonebook to send the code number.
Make a call normally. When you hear the prompt that asks you to enter your number, open the phonebook and find the entry.
Press to send the code. If you change your mind, just close the phonebook.
MENu/sELEcT
Using Call Waiting
x Call Waiting, a service available from your telephone provider, lets you receive calls while you are on another call. Caller ID
on Call Waiting (CIDCW) service displays CID information for a waiting call.
x If you get a Call Waiting call, the phone sounds a tone. Press
call; each time you switch, there is a short pause before you're connected to the other caller.

Finding the Handset

With the phone in standby, press
on the handset.
Using a Voice Mail Service
If you subscribe to a voice mail service, your phone can notify you when you have a new message and give you one-touch access
to your voice mailbox. This feature supports Frequency-Shift Keying (FSK) message notification. Contact your voice mail
provider for more information. The voice mail company will provide you with the access number.
1. With the phone in standby, open the menu and select Global Setup.
2. Select Edit Voice Mail, then enter the access number (up to 20 digits) from your voice mail service. When you're finished,
press .
MENu/sELEcT
New Message Notification
x When you have new messages, the
x To access your mailbox, press
as you entered it.
x After you listen to your messages, the voice message icon turns off. If it doesn't, you can reset it. With the phone in standby,
open the menu and select Global Setup; select VMWI Reset, then select Yes.
Press...
phoNEbook/LEfT, caLLEr Id/rIGhT
or
up
TaLk/fLash
*
before dialing for a toll call.
MENu/sELEcT
number.
MENu/sELEcT
MENu/sELEcT
phoNEbook/LEfT
MENu/sELEcT
to back up the cursor and delete numbers. Re-enter the correct numbers.
MEssaGE/MuTE/cLEar
on the base. The handset will beep for 1 minute. To cancel, press
fINd
LED on the handset blinks, and the display shows a message icon.
sTaTus
when the phone is in standby. The phone dials the access number exactly
MEssaGE/MuTE/cLEar
, or
.
dowN
.
, then select Store Into Pb. Proceed to edit the name and
, then select Edit.
, then select Delete (or Delete Entry). To confirm, select Yes.
.
and then select Create New. Then proceed to enter a name
; you'll see a P in the display. (The dialing will pause for
rEdIaL/pausE
and then select Delete All. To confirm, select Yes.
MENu/sELEcT
to switch between the current call and the waiting
TaLk/fLash
.
rEdIaL/pausE
again or press any key
fINd
English - 5