Functional Description; S P 6 C I F I C A T I O N; P I D C E S E C L A T 6 E - QEP 83200 Owner's Manual

SPECIAT SAFETY INSTRUCTIONS BEFORE USING THE 832OO BRIDGE SAW
Check the following areas;
1. Does the voltage of the motor correspond to the main voltage?
2. A grounded main connection (wall socket) needs to be used.
3 . A r e t h e m a i n l e a d a n d p l u g i n g o o d c o n d i t i o n w i t h o u t a n y l o o s e e n d s o r d a m a g e ?
A. Avoid using long extension cords.
B. Always place the saw on a flat surface to prevent it from tipping over.
While using the saw;
1 . N e v e r u s e - c r a c k e d d i a m o n d b l a d e s . r e p l a c e t h e m
2. Be sure that the switch is in the OFF "OFF'Lposition before connecting the saw to the main voltage.
3. Always keep away the main lead from moving parts of the saw.
4 . D o n o t a p p l y s i d e - p r e s s u r e t o t h e d i a m o n d b l a d e . l t c a n b r e a k t h e b l a d e a n d c a u s e h a r m .
5. Remove the plug out of the wall socket before you make any repairs or replace blade.
IMMEDIATELY SWITCH OFF THE SAW IN CASE OF;
1. Excessive sparking of the brushes.
2 . M a l f u n c t i o n o f t h e m a i n p l u g , s o c k e t o r d a m a g e d c a b l e s .
3 . B r o k e n s w i t c h .
4 . S m o k e o r s m e l l c a u s e d b y s c o r c h e d i n s u l a t i o n .
FUNCTIONAL DESCRIPTION AND OPERATION
STARTING AND STOPPING
1 . C o n n e c t t h e u n i t t o a p o w e r s u p p l y o f t h e c o r r e c t
v o l t a g e a n d f r e q u e n c y ( 1 2 0 V - 6 0 H 2 ) .
2. To start the saw press the switch to the
" O N " p o s i t i o n ( F i g 3 ) .
3 . T o s t o p t h e s a w , p r e s s t h e s w i t c h t o t h e " O F F "
p o s i t i o n ( F i g 3 ) .
WARNING: For your own safety, always position the switch to
the"0ff"position when the saw is not in use. ln the event of a
power failure, blown fuse or tripped circuit breaker, press
switch to the "0t["position. This will prevent the tool from
starting up again when the power comes back on.
ASSEMBLY
Read the manual carefully before assembly.
1 . C l e a n t h e w o r k i n g a r e a .
2 . R e m o v e s a w f r o m c a r t o n , y o u w i l l f i n d
i t a s s e m b l e d .
3 . L a y t h e s a w o n i t s s i d e o n t h e g r o u n d ( F i g a ) .
4 . P u l l o u t t h e s t a n d l e g s , a n d t h e s u p p o r t b r a c k e t s
( F i g 5 - 1 ) . A t t a c h t h e b r a c k e t s t o t h e l e g s w i t h t h e
s u p p l i e d n u t s ( F i g 5 - 2 l ' .
5 . S t a n d t h e s a w u p r i g h t , t h e n p u t t h e s t e e l n e t
b e t w e e n t h e s t a n d l e g s ( F i g 6 ) .
6 . A d j u s t t h e b a l a n c e s c r e w o n r i g h t l e g ( F i g 7 ) .
F i g u r e 3
rc
Figure 4
F i g u r e 5 - 1 Figure 5-2
Figure 6 F i g u r e 7