Buderus 500-24S User Manual
Gas wall hung boiler condensing
Hide thumbs
Also See for 500-24S:
- Installation and maintenance instructions manual (56 pages) ,
- Assembly instructions manual (8 pages) ,
- User manual (28 pages)
Related Manuals for Buderus 500-24S
Summary of Contents for Buderus 500-24S
-
Page 1: Users Manual
7215 3200 – 07/2007 GB/IE (en) For the user Users manual Gas wall hung Boiler condensing Buderus 500-24S Please read thoroughly before operating the unit... - Page 2 DO NOT use abrasive cleaning materials. Gas Council Aplliance No. : Buderus 500-24S : 41-110-24 Buderus • http://www.buderus.co.uk Subject to modifications resulting from technical improvements Users manual for Buderus 500-24S • 07/2007...
-
Page 3: Table Of Contents
Taking the system out of service ..10 11.1 Draining the system in case of frost..10 Subject to modifications resulting from technical improvements Buderus • http://www.buderus.co.uk Users manual for Buderus 500-24S • 07/2007... -
Page 4: Safety Precautions
DBA = Control unit (Dedicated Burner Automat) MCW inlet = Mains Cold Water inlet CH flow = Central Heating flow CH return = Central Heating return. Buderus • http://www.buderus.co.uk Subject to modifications resulting from technical improvements Users manual for Buderus 500-24S • 07/2007... -
Page 5: Permanent Clearances
The installer or service engineer must be able to create sufficient service clearences. These clearences should have been considered at time of installation. Subject to modifications resulting from technical improvements Buderus • http://www.buderus.co.uk Users manual for Buderus 500-24S • 07/2007... -
Page 6: Dba
These keys can be used for adjusting temperatures and activating or de-activating certain summer operation. The C key, when pressed, gives the current operating status of the boiler. Buderus • http://www.buderus.co.uk Subject to modifications resulting from technical improvements Users manual for Buderus 500-24S • 07/2007... -
Page 7: Initial Start-Up
If there are frequent water losses, have the system examined and repaired by a CORGI registered installer. Have the inhibitor concen- tration checked every year. Subject to modifications resulting from technical improvements Buderus • http://www.buderus.co.uk Users manual for Buderus 500-24S • 07/2007... - Page 8 (30 °C – 80 °C) using the C and D keys (see fig. 6, item 1). Factory setting is 80 °C. Buderus • http://www.buderus.co.uk Subject to modifications resulting from technical improvements Users manual for Buderus 500-24S • 07/2007...
-
Page 9: Operational And Fault Codes
CORGI installer. Normal heating Maximum comfort when mode set at 60 °C Normal hot water mode table 1 Operational and fault codes Subject to modifications resulting from technical improvements Buderus • http://www.buderus.co.uk Users manual for Buderus 500-24S • 07/2007... -
Page 10: Taking The System Out Of Service
Drain the system at its lowest point using the stop valves or radiator (see fig. 8). The automatic air vent at the system’s highest point must be open. fig. 8 Draining the system Buderus • http://www.buderus.co.uk Subject to modifications resulting from technical improvements Users manual for Buderus 500-24S • 07/2007... - Page 11 Note Subject to modifications resulting from technical improvements Buderus • http://www.buderus.co.uk Users manual for Buderus 500-24S • 07/2007...
- Page 12 Fax: 01905 - 456 445 / 455 394 Returns: Tel: 01905 - 752 531 Fax: 01905 - 455 392 Spares: Tel: 01905 - 752 576 Fax: 01905 - 754 620 www.buderus.co.uk Buderus is a trading name of BBT Thermotechnology UK Ltd.