Related Manuals for Sony UP-D897
Summary of Contents for Sony UP-D897
- Page 1 2-345-260-15 (1) Digital Graphic Printer Instructions for Use UP-D897 © 2005 Sony Corporation...
- Page 2 Class A digital device, pursuant to Refer to these numbers whenever you call upon your Part 15 of the FCC Rules. These limits are designed to Sony dealer regarding this product. provide reasonable protection against harmful interference when the equipment is operated in a Model No.
- Page 3 UP-D897. Guidance and manufacturer’s declaration-electromagnetic emissions The UP-D897 is intended for use in the electromagnetic environment specified below. The customer or the user of the UP-D897 should assure that it is used in such an environment. Emission test Compliance...
- Page 4 Guidance and manufacturer’s declaration - electromagnetic immunity The UP-D897 is intended for use in the electromagnetic environment specified below. The customer or the user of the UP- D897 should assure that it is used in such as environment. IEC 60601 test...
- Page 5 Guidance and manufacturer’s declaration - electromagnetic immunity The UP-D897 is intended for use in the electromagnetic environment specified below. The customer or the user of the UP- D897 should assure that it is used in such as environment. IEC 60601 test...
- Page 6 Recommended separation distances between portable and mobile RF communications equipment and the UP-D897 The UP-D897 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the UP-D897 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (Transmitters) and the UP-D897 as recommended below, according to the maximum output power of the communications equipment.
-
Page 7: Table Of Contents
Table of Contents Getting Started Overview ..............8 Location and Function of Parts and Controls ..8 Front Panel ............8 Rear Panel ............9 Connections ............9 Connecting to the USB Connector ..... 9 Installing the Printer Driver ........ 9 Paper .............. -
Page 8: Getting Started
Getting Started Location and Function of Parts and Controls For more details, see the referenced page numbers Overview enclosed in parentheses ( ). Quiet, High Quality, Fast Printing Front Panel • Employs a thin thermal head with a built-in high speed drive IC, capable of high resolution images of 12.8 dots/mm. -
Page 9: Rear Panel
• Printer operation is not guaranteed when connecting to the computer using the USB cable via a hub. Connecting to the USB Connector UP-D897 (USB) connector USB connector (9) Connects to a computer equipped with the USB USB connecting interface (which conforms to USB 2.0), using the... -
Page 10: Paper
Paper Loading Paper in the Unit Use only Sony UPP-110S/110HD/110HG paper designed for use with this unit. High print quality cannot be guaranteed if any other paper is used with this unit, Notes and such paper could damage the unit. - Page 11 Press the OPEN button to open the paper door. Make sure that the paper is set straight. Close the paper door and press on it to shut it. Remove the label from the leading edge of the paper, pull out about 15~20 cm (about 6~8 in.) of the paper, and then set the paper roll in the paper tray.
-
Page 12: Operation
You can set up the unit according to its intended Operation purpose, connected equipments or your individual preferences. You can store up to three settings as a set of user settings. Adjustments and Settings Using the Menu You can carry out adjustments and settings to meet your requirements. -
Page 13: Menu List
D895. information) are item selection column. [CO:897]: Uses the printer printed under the driver for the UP-D897. image BACK: Cancels the setting LOAD To load the LO:3: Loads the “SA:3” change and returns to the... -
Page 14: Basic Menu Operations
a) The printing direction is as follows. Item Function Settings [RS:OFF]: Prints the image RSIZE To select whether or not the image at the original size. is enlarged RS:ON: Prints the image at a larger size, according to the paper size set by the printer driver. - Page 15 The back light on the LCD lights in green. Press the jog dial. The unit enters the mode in which you can select Confirm that “READY” is displayed on the LCD, the printing direction. and press the jog dial. “DI:NOR,” which is the factory setting, is displayed on the LCD.
-
Page 16: Registering Menu Settings
To cancel the setting Display “LOAD” by turning the jog dial, and then press the jog dial again. 1 Display “BACK” by turning the jog dial in step Display the number corresponding to the desired settings, and then press the jog dial. 2 Press the jog dial. -
Page 17: Printing
In the following figure, the currently selected paper is Printing the UPP-110S paper. Before Starting a Print Job Indicates the UPP-110S Always check the following points: Indicates the UPP-110HD • unit connected correctly? (page 9) • Printer driver installed? (page 9) Indicates the UPP-110HG •... -
Page 18: Adjusting The Contrast And Brightness
Adjusting the Contrast and Brightness You can adjust the contrast and brightness of the unit using the CONTR control and BRIGHT control on the front panel. To adjust the contrast You can adjust the contrast of printouts using the CONTR control. To make the contrast stronger: Turn the CONTR control clockwise. -
Page 19: Others
ventilation holes (intake) on the left hand side and the Others ventilation holes (exhaust) on the rear of the cabinet. Precautions On Safety • Check the operating voltage before operation. Operate the unit only with a power source specified in “Specifications”. -
Page 20: Maintenance
Insert the cleaning sheet, with the black surface Maintenance facing down, into the groove of the paper tray. Insert the Cleaning the Cabinet cleaning sheet into the Use a wrung out damp cloth, or a damp cloth soaked in groove of the water and a mild detergent, to clean the cabinet surface. -
Page 21: Cleaning The Platen Roller
Press and hold down the FEED button so that the Cleaning the Platen Roller platen roller turns automatically. Release the FEED When the surface of the platen roller gets dirty, paper button when the surface of the platen roller to be will not be ejected smoothly after printing, resulting in cleaned appears. -
Page 22: Specifications
1280 dots) (printing at the normal SOFTWARE, EXTERNAL STORAGE, OR speed) OTHER EXTERNAL DEVICE. Picture elements • SONY WILL NOT BE LIABLE FOR DAMAGES 4096 × 1280 dots (max.) OF ANY KIND INCLUDING, BUT NOT Dot density H: 100 mm/1280 dots = 0.078 LIMITED TO, COMPENSATION OR V: 100 mm/1280 dots = 0.078... -
Page 23: Troubleshooting
Troubleshooting Error Messages Before you call for service, please check the problems Messages appear on the LCD under the following and solutions described below. If you cannot solve the conditions. Take the remedial actions shown next to the problem, contact the nearest authorized dealer. messages to correct the problem. -
Page 24: Index
Index Specifications 22 Troubleshooting 23 Connections 9 Error messages 23 Getting Started 8 Location and function of parts and controls front panel 8 rear panel 9 Maintenance cleaning the cabinet 20 cleaning the platen roller 21 cleaning the thermal head 20 Menu basic operations 14 list 13... - Page 25 Sony Corporation...