Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Denwa Communications DW-V-AXT-ANDROID
Summary of Contents for Denwa Communications DW-V-AXT-ANDROID
-
Page 2: Table Of Contents
Content Product Overview ................4 1. Product Description .................... 4 2. Features ....................... 5 3. Dimension ......................7 4. Installation height ....................8 5. Adjust camera angle .................... 9 Web UI& Operation ..............11 1. Main interface ....................11 2. Calling out ......................11 3. - Page 3 5.Phone-> Dial Plan->Replace Rule ............... 45 6.Phone-> Door Setting ..................46 7.Phone->Import/Export ..................50 8.Upgrade-> Basic ....................51 9.Upgrade-> Advanced ..................52 10.Security-> Basic ....................54 Troubleshooting ................55...
-
Page 4: Product Overview
Product Overview 1.Product Description The Denwa DW-V-AXT-ANDROID is the video door phone, that you can connect with your Denwa IP Phones for remote unlock control and monitoring. You can operate the indoor handset to communicate with visitors via voice and video, and unlock the door if you wish. -
Page 5: Features
2.Features Phone Features HD Voice 2 Lines (support 2 SIP accounts) Phonebook (1000 Contacts, 100 Groups) Volume Adjustable Auto Answer Dial Replace Rule Wideband Codec: G.722 Narrowband Codec: PCMA, PCMU, G.729 AGC, Echo Canceller ... - Page 6 Maximum image transfer rate: 1080p - 30fps Video codecs: H.263, H.264 High intensity white LEDs for picture lighting during dark hours with internal light sensor Network Features SIP V1(RFC2543), V2(RFC3261) 3 DTMF modes: In-Band,RFC2833,SIP INFO ...
-
Page 7: Dimension
3. Dimension... -
Page 8: Installation Height
4. Installation height *It is recommended that the distance between camera and ground remains 1.6m. -
Page 9: Adjust Camera Angle
5. Adjust camera angle... -
Page 10: Web Ui& Operation
Web UI & Operation 1. Main interface The default screen after boot up is the password unlock screen, touch to switch screen to dial pad. 2. Calling out In dial pad, input desired number than press to dial out. The screen will turn to calling, or talking when there is a conversation. -
Page 11: Unlock By Rf Card
4. Unlock by RF card Place RF card close to sensor area, if the card was bound to the door phone before, screen will prompt “Open Lock Success”. For RF card recognition, please refer to “RF card” in Configuration section. -
Page 12: Configuration In Doorphone
Configuration in Door Phone To configure each feature on DW-V-AXT-ANDROID, user need activate Factory setting mode. On the dial mode, dial “9999” then press “dial”. When prompt Setting interface, press “3888”(default) then “OK” to enter Factory setting. -
Page 14: Configure Address
Configure Address DHCP: Connect the Ethernet cable and tick DHCP. The device will access the network parameter automatically. Static IP: Press “Address” to setup network address, and then input “IP Address”, “Subnet Mask” & “Gateway” to modify default parameters. Press “Save” to save configuration. -
Page 15: Configure Password
Configure Password To configure unlock or factory setting password for door phone, Press “Password” to enter password setting mode. Under “Project password” interface, input old password (“9999” by default) and new password, confirm the new password again, and then press “Save” to save configuration. -
Page 16: Account
Account DW-V-AXT-ANDROID supports 2 lines. To register an SIP platform, Input account, password, SIP server IP and port. Once finished, press “Save” then the door phone will send out registration detail to the server. Note: Account 2 is only used to answer the phone. -
Page 17: Contact
Contact Users not only can add the new contact in the Contact interface, also can edit or delete. Mean while, users can create groups, then add the contact to the corresponding group. -
Page 18: Time
Time To configure doorphone time, please press “Time” to enter time setup interface. User can adjust both Date, Time and Time zone manually, or just tick Automatic date&time, the device will access the time information automatically. Click Save to save the configuration. -
Page 19: Volume
Volume To configure doorphone volume, please press “Volume” to enter volume setup interface. User can adjust three types of volume: Call, Advertisement and key. Then press “Save” to save configuration. -
Page 20: Info
Info To view system information, press “Info” on the screen. It includes Machine number, network address, MAC address, Software version and hardware version. Lock Press “Lock” to configure door lock and door sensor. Door lock can be configure as “Positive” or “Negative”. “Positive” is usually apply for uni-direction situation, it is better to have UPS power when apply this door type, since the door will be locked when power disaster. - Page 21 period. And this period can be setup in Magnetism delay. User can setup DTMF code. It is used for the owner to unlock via pressing the corresponding number during the call.
-
Page 22: Await
Await In “Await”, there are three options for standby mode “No”, “Blank Screen”, “Picture”. Screen will enter standby mode when reach Standby time, and user can customize standby time according to their needs. Unlock Mode is used for wake up the await interface. -
Page 23: Lock Password
Lock Password To setup the private key to unlock. Click Add Private Key, and input 8 digit codes, press Save. User can also configure Day and Time of the private key to limit permission. Click the exited code to edit or delete. Restore Factory Reset will reset all configuration to default, please be cautious to use this feature. -
Page 24: Antialarm
AntiAlarm To protect door phone from any malicious damage, user can enable protection in “Tamper Proof Switch”. When tamper switch is on, any tamper movement will trigger alarm. If trigger the alarm accidently, user need to enter Tamper Sets and turn off Tamper switch manually. -
Page 25: Replacerule
ReplaceRule Allow user to add replace rule, you can modify related accounts, prefix and replace. -
Page 26: Rf Card
RF card Enter “RF card” to add or delete the RF card. After the card has been registered, users can use it to unlock. Add card: Press “Add Card”, it will show up a prompt “Please scan the RFCard to Add”. ... -
Page 27: Reboot
Delete card: Press “Del Card”, it will show up a prompt “Please scan RFCard to Delete”. Put card near the card sensor. The device will show up the modify prompt, click Del to delete the RFCard. Note: User can click exited RFCard, then select Del directly. -
Page 28: Rtsp
RTSP DW-V-AXT-ANDROID Enable the RTSP function for monitoring . The administrator can view the video from the door phone any time with the Onvif software. Motion Motion detection is used for recording any change of the surrounding environment. DW-V-AXT-ANDROID User can enable the motion function in and setup the other parameters on the web. - Page 29 Motion detection supports two modes: FTP and EMAIL. Choose the notification mode first. Setup the Detection Delay, Capture Delay and Detection Accuracy time. FTP Mode: 1. Enable the FTP server and configure the user name and password. 2. Create a folder named “picture” 3.
-
Page 30: Device
Device User can setup the device name to limit the unlock permissions. Setup the LED, the device will automatic adjust backlight in the Insufficient light environment. It can support three modes. Click the Threshold key, it will automatic show the current intensity. Once the environment intensity is darker than the Threshold, the backlight will be up. -
Page 31: Configuration In Website
Configuration in website Enter the door phone IP into the website. Input the username and password (the user name is admin, the password is admin by default) to login in. 1.Status-> Basic To check the information of the doorphone, included product information、network information and account information. -
Page 32: Account-> Basic
Address, Subnet Mask, Gateway, Primary DNS server, Secondary DNS server, Primary NTP server Account Information To display device’s Account information and Registration status (account username, registered server’s address, Register result). 2.Account-> Basic To register some sip accounts. Go to the path: Web UI-> Account-> Basic... - Page 33 Sections Description SIP Account To display and configure the specific Account settings. Status: To display register result. Display Label: Which is displayed on the phone’s LCD screen. Display Name: Which is sent to the other call party for displaying.
-
Page 34: Account-> Advanced
3.Account-> Advanced To configure more settings of the account. Go to the path: Web UI-> Account-> Advanced... - Page 35 Sections Description SIP Account To display current Account settings or to select which account to display. Codecs To display and configure available/unavailable codecs list. Codec means coder-decoder which is used to transfer analog signal to digital signal or vice versa. Familiar codecs are PCMU(G711U), PCMA(G711A), G722 (wid-bandth codecs),G729.
- Page 36 from SIP server. User=phone: If enabled, IP phone will send user=phone within SIP message. Anonymous Call: If enabled, all outgoing call for the designated account will be anonymous number. Anonymous Call Rejection: If enabled, all incoming anonym-out call for the designated account will be rejected.
-
Page 37: Phone-> Call Feature
4.Phone-> Call Feature To setup different call settings. Go to the path: Web UI-> Phone-> Call Feature Sections Description Mode To enable or disable feature key sync. Feature Key Sync: To enable or disable feature key sync. Mode: Select the desired mode. DND (Do Not Disturb) allows IP phones to ignore any incoming calls. - Page 38 when DND is off. DND Off Code: The Code used to turn off DND on server’s side, if configured, IP phone will send a SIP message to server to turn off DND on server side if you press DND when DND is Call Waiting To enable or disable Call Waiting.
-
Page 39: Phone-> Dial Plan->Replace Rule
5.Phone-> Dial Plan->Replace Rule Go to the path: Web UI-> Phone-> Dial Plan Sections Description Rules Allow user to select Replace rule or Dial-now to display or edit. Rules Modify Allow user to modify selected rules information, for replace rule, you can modify related accounts, prefix and replace. Area Code Area codes are also known as NPAs (Numbering Plan Areas). -
Page 40: Phone-> Door Setting
6.Phone-> Door Setting Go to the path: Feature->Door setting Sections Description Door Setting General General setting allows users to control the default display when the device is turned on . Configuring display number when you input the number to call the host. And control whether turn on the tamper alarm. - Page 41 Enable RTSP for Onvif function. RTSP Web Relay Connect external web relay. Type: Select 2N WebRelay to enable this function. And DW-V-AXT-ANDROID relay will be disabled. IP Address: Setup web relay IP address. UserName: Setup web relay user name. Password: Setup web relay password.
- Page 42 BuildNo: Setup the Build number as the other side has. UnitNo: Setup the Unit number as the other side has. Floor: Setup the Floor number as the other side has. RoomNo: Setup the RoomNo as the other side has. DW-V-AXT-ANDROID DeviceNo: Setup serial number...
-
Page 43: Phone->Import/Export
7.Phone->Import/Export Go to the path: Web UI-> Phone-> Import/Export Sections Description Import/Export Config Contact: Click Export to export the existed contact. Choose the local file and click Import to import the new contact. The export format is “.vcf”, the import format is “.vcf”、... -
Page 44: Upgrade-> Basic
uploaded. It can only support “.jpg” format. 8.Upgrade-> Basic Go to the path: Web UI-> Upgrade-> Basic Sections Description Upgrade To select upgrading zip file from local side. Note: Please make sure it’s right file format for right model. Firmware version To display firmware version, firmware version starts with MODEL name. -
Page 45: Upgrade-> Advanced
9.Upgrade-> Advanced Go to the path: Web UI-> Upgrade-> Advanced Sections Description PNP Option To display and configure PNP setting for Auto Provisioning. PNP: Plug and Play, once PNP is enabled, the phone will send subscription message server automatically to get Auto Provisioning server’s address. By default, this SIP message is sent to multicast address 224.0.1.75(PNP server address by standard). -
Page 46: Security-> Basic
common Auto Provisioning configuration file. AES Key(MAC): Used for IP phone to decipher MAC- oriented auto provisioning configuration file(for example, file name could be 0c1105888888.conf if IP phone’s MAC address is 0c1105888888). Note: AES is one of many encryption, it should be configure only configure filed is ciphered with AES, otherwise left blank. -
Page 47: Troubleshooting
Sections Description Web Password Modify To modify user’s password. Current Password: The current password you used. New Password: Input new password you intend to use. Confirm Password: Repeat the new password. Note: For now, IP phone can only support user admin. Troubleshooting ...