Specification; Specific Safety Rules - Makita HR2010 Instruction Manual

ENGLISH
1 Bit grease
2 Bit shank
3 Bit
4 Chuck cover
5 Side grip
6 Loosen

SPECIFICATION

Model
Capacities
Concrete ............................................................ 20 mm
Wood ................................................................. 24 mm
Steel .................................................................. 13 mm
–1
No load speed (min ).......................................... 0 – 900
Blows per minute .............................................. 0 – 4,000
Overall length ...................................................... 302 mm
Net weight ............................................................. 3.2 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to rotary hammer safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Wear ear protectors. Exposure to noise can cause
hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
4. Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
5. Be sure the bit is secured in place before opera-
tion.
6. Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
4
Explanation of general view
7 Tighten
8 Grip base
9 Clamp screw
10 Depth gauge
11 Switch trigger
12 Chuck adapter
7.
HR2010
8.
9.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
12. Do not point the tool at any one in the area when
13. Do not touch the bit or parts close to the bit
14. Some material contains chemicals which may be
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
GEB007-2
OPERATING INSTRUCTIONS
Installing or removing drill bit (Fig. 1, 2 & 3)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Clean the bit shank and apply bit grease before installing
the bit. (Fig. 1)
Insert the bit into the tool. Turn the bit and push it in until
it engages. (Fig. 2)
If the bit cannot be pushed in, remove the bit. Pull the
chuck cover down a couple of times. Then insert the bit
again. Turn the bit and push it in until it engages. (Fig. 3)
After installing, always make sure that the bit is securely
held in place by trying to pull it out. To remove the bit, pull
the chuck cover down all the way and pull the bit out.
Side grip (Auxiliary handle) (Fig. 4)
The side grip swings around to either side, allowing easy
handling of the tool in any position. Loosen the side grip
by turning it counterclockwise, swing it to the desired
position and then tighten it by turning clockwise.
13 Drill chuck
14 Screw driver
15 Brush holder cap
16 Lock nut wrench
17 Crank cap
18 Hammer grease
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
Hold the tool firmly with both hands.
only when hand-held.
operating. The bit could fly out and injure some-
one seriously.
immediately after operation; they may be
extremely hot and could burn your skin.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.