Specification; Additional Safety Rules - Makita HR2010 Instruction Manual

ENGLISH
1 Bit grease
2 Bit shank
3 Bit
4 Chuck cover
5 Side grip
6 Loosen

SPECIFICATION

Model
Capacities
Concrete ............................................................ 20 mm
Wood ................................................................. 24 mm
Steel .................................................................. 13 mm
–1
No load speed (min ) .......................................... 0 – 900
Blows per minute .............................................. 0 – 4,000
Overall length ...................................................... 302 mm
Net weight .............................................................. 3.2 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear protec-
tors and thickly padded gloves.
2. Be sure the bit is secured in place before opera-
tion.
3. Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
4. In cold weather or when the tool has not been
used for a long time, let the tool warm up for sev-
eral minutes by operating it under no load. This
will loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
5. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
6. Hold the tool firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the tool running. Operate the tool
only when hand-held.
9. Do not point the tool at any one in the area when
operating. The bit could fly out and injure some-
one seriously.
Explanation of general view
7 Tighten
8 Grip base
9 Clamp screw
10 Depth gauge
11 Switch trigger
12 Chuck adapter
10. When drilling or chipping into walls, floors or
HR2010
11. Do not touch the bit or parts close to the bit
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing drill bit (Fig. 1, 2 & 3)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Clean the bit shank and apply bit grease before installing
the bit. (Fig. 1)
Insert the bit into the tool. Turn the bit and push it in until
it engages. (Fig. 2)
If the bit cannot be pushed in, remove the bit. Pull the
chuck cover down a couple of times. Then insert the bit
again. Turn the bit and push it in until it engages. (Fig. 3)
After installing, always make sure that the bit is securely
held in place by trying to pull it out. To remove the bit, pull
the chuck cover down all the way and pull the bit out.
Side grip (Auxiliary handle) (Fig. 4)
The side grip swings around to either side, allowing easy
handling of the tool in any position. Loosen the side grip
by turning it counterclockwise, swing it to the desired
position and then tighten it by turning clockwise.
Depth gauge (Fig. 5)
The depth gauge is convenient for drilling holes of uni-
form depth. Insert the depth gauge into the hole in the
grip base. Adjust the depth gauge to the desired depth
and then tighten the clamp screw to secure the depth
gauge.
NOTE:
The depth gauge cannot be used at the position where
the depth gauge strikes against the gear housing.
13 Drill chuck
14 Screw driver
15 Brush holder cap
16 Lock nut wrench
17 Crank cap
18 Hammer grease
wherever "live" electrical wires may be encoun-
tered, DO NOT TOUCH ANY METAL PARTS OF
THE TOOL!
Hold the tool by the insulated grasping surfaces
to prevent electric shock if you drill or chip into a
"live" wire.
immediately after operation; they may be
extremely hot and could burn your skin.
5