CHAPTER 1: INTRODUCTION 1.1 An Overview of the del Wireless 108Mbps Multi-Function Access Point 1.2 Package Contents 1.3 Wireless Multi-Function Access Point Features 1.4 System Requirements 1.5 Setup 1.6 Location CHAPTER 2: USING WIRELESS ACCESS POINT 2.1 Cautions for using the Wireless Access Point 2.2 The Front LEDs 2.3 The Rear Ports 2.4 Cabling...
Page 4
APPENDIX A: TROUBLESHOOTING A.1 Using LEDs to Diagnose Problems A.1.1 LED Power A.1.2 LED LAN A.1.3 LED WLAN A.2 WEB A.3 Login A.4 FAQ APPENDIX B: TECHNICAL FEATURES APPENDIX C: SUPPORT A02-WAP-54G(V1.1)_ME01 (V1.0 May 2007) Wireless 108Mbps Multi-Function Access Point...
Page 5
Windows™ 98SE/2000/ME/XP are trademarks of Microsoft® Corp. Pentium is trademark of Intel. All copyright reserved. The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other names mentioned mat be trademarks or registered trademarks of their respective owners.
Page 6
CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. CE in which Countries where the product may be used freely: Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland, Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland.
Page 7
Wireless 108Mbps Multi-Function Access Point 2) This device must accept any interference received, including interference that may cause undesired operation.
IEE802.11G you are going to have a fast and flexible wireless net, hacker safe. The chipsets fully support Wi-Fi Protected Access (WPA/WPA2) and the IEEE802.11i draft security standards in hardware and high-speed encryption engines with no performance degradation. A02-WAP-54G Pag. 1...
Repeater: Repeat Mode is able to extend the effective range and coverage of the wireless network. • Client Wireless: the AP will be a wireless Ethernet adapter transforms any Ethernet-enabled devices to have the wireless function. Wireless 108Mbps Multi-Function Access Point The chipsets fully support Wi-Fi A02-WAP-54G Pag. 2...
Normally, the higher you place the antenna, the better the performance will be. The antenna’s position enhances the receiving sensitivity. • Visually inspect if the Power Adapter was fully plugged to the device power jack. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 3...
Try to place the AP in a position that can best cover your wireless network. Normally, the higher you place the antenna, the better the performance will be. The antenna’s position enhances the receiving sensitivity. A02-WAP-54G Pag. 4...
Place the Wireless Access Point on a stable surface. Only use the power adapter that comes with the package. Do NOT upgrade firmware on any Atlantis Land product over a wireless connection. Failure of the device may result. Use only hard-wired network connections.
The Reset function is to reset the setting back to factory default setting, once you press the “RESET” button more than 10 seconds. Ethernet port with 10/100Mbps Fast Ethernet connections, connect this port to switch/hub. Connect the Power Adapter DC plug to the AP’s power jack. A02-WAP-54G Pag. 6...
If the LAN Port’s Link indicator does not light up then check the RJ-45 cable if it is firmly feed to the RJ45 port, while the LAN is link up to the Switch/Hub, the LAN port’s LED will light up. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 7...
Ethernet network adapter must be installed. If not, please refer to MS Windows related manuals. Any TCP/IP capable workstation can be used to communicate with or through the Wireless Access Point to configure other types of workstations, please consult the manufacturer’s documentation. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 8...
3.1.1 Windows 95/98/ME Wireless 108Mbps Multi-Function Access Point 1. Go to Start / Settings / 2. Select TCP / IP -> NE2000 3. Click Properties. 4. Select the IP Address tab. In A02-WAP-54G Control Panel. In the Control Panel, double-click Network choose Configuration tab.
Panel. In the Control Panel, double- click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the IP Address tab. In this page, click the Specify an IP address IP=192.168.1.2 Mask=255.255.255.0). A02-WAP-54G radio button subnet Pag. 10...
1. Go to Start / Settings / Control 2. Double-click 3. In the LAN Area Connection 4. Select 5. Select Use the Following IP 6. Click A02-WAP-54G Panel. In the Control Panel, double-click on Network and Dial-up Connections. Connection. Status window, click Properties.
3.1.4 Windows XP Wireless 108Mbps Multi-Function Access Point A02-WAP-54G 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double- click Network Connections. 2. Double-click Local Area Connection 3. In Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) Properties.
3.2.2 LAN WLAN The parameters of LAN and WLAN ports are pre-set in the factory. The default values are shown below. IP address Subnet Mask Wireless 108Mbps Multi-Function Access Point 192.168.1.1 255.255.255.0 A02-WAP-54G WLAN Channel=6 SSID=default Encryption=none Pag. 13...
When there is a screen needs to enter the User name and Password, both of the default Username and Password is “admin”. Click OK. The screen will show the station summary of the AP when you login to the AP. A02-WAP-54G Pag. 14...
There are seven main functions included in the top side of the main screen: • Wizard • Status • Basic Setting • IP Setting • Advanced Setting • Security • Tools Point the selections in the top side of the menu screen. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 15...
Wireless 108Mbps Multi-Function Access Point 3.4 Wizard Quick Wizard Setup The following screen will appear. Please click Next to continue. You also can go back to modify the setting by clicking Back (when available). A02-WAP-54G Pag. 16...
Page 24
Wireless 108Mbps Multi-Function Access Point Step 1: Set Password You can change the password as you like and then click Next to continue. A02-WAP-54G Pag. 17...
Page 25
Click enable to enable wireless LAN. If you enable the wireless LAN, type the SSID in the text box and select a communications channel. The SSID and channel must be the same as wireless devices attempting communication to the Access Point. Select a channel number and click on Next. A02-WAP-54G Pag. 18...
Page 26
Step 3: Set WEP Encryption If user wants to enable WEP, please click Enabled. Then, select the key size of WEP encryption and enter the key value in the key text box. Please click Next to continue. A02-WAP-54G Pag. 19...
Page 27
The Setup wizard is now completed. The new settings will be effective after the Wireless 108Mbps Access Pointrestarted. Please click Restart (then Close) to reboot the Access Point. If you do not want to make any changes, please click exit to quit without any changes. A02-WAP-54G Pag. 20...
AP through wired connection is also displayed. Wireless: Shows the Mac address, current SSID, the status of Encryption Function (Enable or Disable), the current using channel. The current wireless Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 21...
SSID: Service Set Identifier, which is a unique name shared among all clients and nodes in a wireless network. The SSID must be identical for each clients and nodes in the wireless network. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 22...
Page 30
AP should be on a channel at least five channels away from a channel that an adjacent AP is using. For example, if your region has 11 channels and an adjacent AP is using channel 1, then you need to select a channel between 6 or 11. A02-WAP-54G Pag. 23...
WPA-PSK / WPA2-PSK: If WPA-PSK or WPA2-PSK is selected, user needs to set the key in the passphrase field as the below screen. The key length should be 8 characters at least. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 24...
Page 32
Secret, which is used by the Radius Server. Apply: For the changes made to any of the items above to be effective, click “Apply”. The new settings are now been saved to Access Point and will be effective once the Access Point restarts. A02-WAP-54G Pag. 25...
“On”, and enter the IP range. DNS Server: Type up to DNS IP address in the text boxes. Your ISP will provide you with this information. Click “Apply” for the changes to be effective. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 26...
DTIM Interval: This value indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 27...
Page 35
G. Static turbo means it will not go back to ‘normal’ G once it starts. Antenna transmit power: Adjust the power of the antenna transmission by selecting from the drop down list for full, half (-3dB), quarter (-6dB), eighth (- 9dB) and min. Aging Interval: To limited STA connect timing. A02-WAP-54G Pag. 28...
Wireless 108Mbps Multi-Function Access Point 3.8.1 AP Mode Configure the AP to Access Point mode; with this mode, WLAN clients can access LAN or other WLAN clients through this AP. AP Mode: Select Access Point. A02-WAP-54G Pag. 29...
AP Mode: Select AP Client. Click Site Survey. Chose the correct Wireless network, then click on Connect. You must make sure that Encryption is set the same as that AP you wish to connect. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 30...
You must make sure that the SSID, Encryption and Channel is set the same as that AP you wish to connect. When Wireless Bridge / Wireless MultiBridge ecryption is supported. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G is enable only WEP Pag. 31...
Page 39
Slave need to fill the Master’s MAC address in the “Remote Bridge Mac” list. In this example, LAN-A can communicate with LAN-B and LAN-C, and LAN-B can communicate with LAN-C through the AP-A. All of LANs will be at the same LAN environment coming through LAN-A. A02-WAP-54G Pag. 32...
Chose the correct Wireless network, then click on Connect. You must make sure that Encryption is set the same as that AP you wish to connect. When Repeat Mode is enable only WEP ecryption is supported. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 33...
Password: Allow user to change the new login password. Here are the necessary steps: Enter the new password in the “AP Password New:” field. Enter the new password again in the “Confirm” field. Click “Apply” Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 34...
Page 42
The maximum number of MAC addresses that can be stored is 50. User can browse through the MAC address saved by selecting the MAC Filter List. For any changes made in the security page, click “Apply” for the changes to be effective. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 35...
Upon selecting the saved file, click “Restore” and complete the restore process when the access point re-operates after it restarts. Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 36...
Page 44
Upon selecting the firmware file, click “Upgrade” and complete the firmware upgrade process when the Access Point re-operates after it restarts. Do NOT upgrade firmware on any Atlantis Land product over a wireless connection. Failure of the device may result. Use only hard-wired network connections.
Check for faulty Ethernet cables. Make sure your computer’s Ethernet card is working properly. If these steps fail to correct the problem, contact your local distributor for assistance. Wireless 108Mbps Multi-Function Access Point CORRECTIVE ACTION CORRECTIVE ACTION A02-WAP-54G Pag. 38...
If you forget the password to log in Steps The Reset function is to reset the setting back to factory default setting, once you press the “RESET” button within 10 Wireless 108Mbps Multi-Function Access Point CORRECTIVE ACTION CORRECTIVE ACTION CORRECTIVE ACTION CORRECTIVE ACTION A02-WAP-54G Pag. 39...
Page 47
Before configurating thisWireless Multi-Function Access Point, you need to know the following default settings. Username: admin Password : admin IP Address : 192.168.1.1 Subnet Mask : 255.255.255.0 Wireless: SSSID= default, Channel=6, WEP=disable A02-WAP-54G Pag. 40...
The longer the chip, the greater the probability that the original data can be recovered. Even if one or more Wireless 108Mbps Multi-Function Access Point Spread-Spectrum both transmitter impulse noise. A02-WAP-54G (FHSS) uses receiver. Properly Direct-Sequence Spread- Pag. 41...
Page 49
Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe. A02-WAP-54G Pag. 42...
Page 50
54 megabits per second (Mbps) compared with the 11 megabits per second of the 802.11b (Wi-Fi) standard. Like 802.11b, 802.11g operates in the 2.4 GHz range and is thus compatible with it. A02-WAP-54G Pag. 43...
Page 51
Wireless 108Mbps Multi-Function Access Point A02-WAP-54G Pag. 44...
5W (Max) Operating: 0 ~ 40 Operating: 10% ~ 90%, Storage: 5% ~ 90% 140 x 98 x 30 mm (W x H x D) without Antenna FCC Class B, CE Mark B A02-WAP-54G C, Storage: -10 ~ 70 Pag. 45...
If you continue to have problems you should contact the dealer where you bought this device. If you have any other questions you can contact the Atlantis Land company directly at the following address: Atlantis Land SpA Viale De Gasperi 122...