Internet Connection Feature - Yaesu FT-8800R Operating Manual

I
NTERNET
The FT-8800R can be used to access the repeater which is configured to provide access to
the Vertex Standard WIRES
1. Press the "left" VOL knob momentarily to activate the WIRES™ access capability. The
"INT ON INT ON" will appear for 2 seconds at the "Main" band frequency display. The "int
INT ON INT ON
INT ON
icon will appear in the memory channel field on the "Sub" band while WIRES
is enabled.
2. Rotate the "Main" band DIAL knob, while pressing and holding in the "left" VOL knob,
to select the access number (ICODE
corresponding to the WIRES
(ask your repeater owner/operator if you don't know the access numbers in the net-
work).
3. With the WIRES™ capability activated (as in step 1 above), the FT-8800R will gener-
ate a brief (0.1 second) DTMF tone according to your selection in step 2. This DTMF
tone is sent at the beginning of every transmission to establish or maintain the link to the
remote WIRES
TM
4. To disable the WIRES
You may access other Internet Link Systems that use a DTMF string for access.
1. Press the [ SET ] key momentarily to enter the Set mode.
2. Rotate the "Main" band DIAL knob to select Menu #15 (DTMF W
3. Press the "Main" band DIAL knob momentarily, then load the DTMF tones which you
wish to use to establish an Internet link (ask your repeater owner/operator if you don't
know the access numbers in the network) into the desired DTMF Memory channel.
1) Rotate the "Main" band DIAL knob to select the DTMF Autodialer memory channel
number ("d-1 d-1" through "d-16
d-1 d-1
d-1
2) Press the "Main" band DIAL knob momentarily.
3) Rotate the "Main" band DIAL knob to select the DTMF code, then press the "Main"
band DIAL knob momentarily to move the digit.
4) Repeat step 3) above.
5) Press the "Main" band DIAL knob momentarily to save the new setting.
4. Rotate the "Main" band DIAL knob to select Menu #17 (INET
5. Press the "Main" band DIAL knob momentarily, then rotate the "Main" band DIAL
knob to set this Item to "INT.MEM
the WIRES™ access option).
6. Press and hold in the "Main" band DIAL knob for 1/2 second to save the new setting
and exit to normal operation.
7. Press the "left" VOL knob momentarily to activate the Internet Link System. The "INT
ON" display will appear for 2 seconds in the "Main" band frequency field. The "int
ON ON
ON ON
icon will then appear in the memory channel field on the "Sub" band while the Internet
Link System access feature is engaged.
50
C
ONNECTION
(Wide-Coverage Internet Repeater Enhancement System).
TM
ICODE "0 0 0 0 0 " ~ "9 9 9 9 9 ," "A A A A A ," "B B B B B ," "C C C C C ," "D D D D D ," "E E E E E ( )," or "F F F F F (#)")
ICODE ICODE
ICODE
repeater to which you wish to establish an Internet link
TM
repeater.
access capability, press the "left" VOL knob again.
TM
d-16 d-16"). d-16
d-16
INT.MEM" (to enable the alternative Internet Link, and disable
INT.MEM INT.MEM
INT.MEM
F
EATURE
DTMF W DTMF W DTMF W). DTMF W
INET). INET INET
INET
FT-8800R Operating Manual
int int" int int
access
TM
INT INT INT
INT
int int" int int