Sony HCD-RV777D Service Manual page 28

HCD-RV777D/RV888D/RV999D
QQ
3 7 63 1515 0
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is displayed
when a disc is loaded.
Note:
1. Set correctly the disc type to be used on the Disc Type
screen.
2. In case of an alarm, immediately press the x button to
stop the servo operation, and press the +/1 button to
turn the power off.
Basic operation:
(controllable from front panel or remote commander)
+/1 : Power OFF (release the Test Mode)
x
: Servo stop
Z
: Stop and eject/Loading
ENTER : Return to Operation Menu or Test
Mode Menu
. , >
: Transition between sub modes of
menu
1 to 9 , 10/0 : Selection of menu items
Cursor o / O : Increase/Decrease in manually
adjusted value
2-1. Disc Type
Disc Type
Disc Type Select
TE
L 13942296513
1. Disc Type Auto Check
2. Set Disc Type DVD
3. Set Disc Type CD
4. Set Disc Type Hybrid
2-1-1. Disc Type Auto Check
1) Press the 1 button on the remote commander to display the
Disc Type Auto Check screen.
2) Insert a disc and press the ENTER button on the remote
commander.
3) It judges the type of inserted disc automatically and displays
the disc type and so on as below.
Disc Type Auto Check
Disc Type xx
Layer xx
Mirr Time xx
Mirr Count xx
FZC Count xx
PI Reference xx
PI Peak xx
www
ENTER.Execute
.
Disc Type : CD, DVD or Hybrid (SACD)
Layer : SINGLE, DUAL or HYBRID
28
http://www.xiaoyu163.com
Exit: RETURN
x ao u163
y
Exit: RETURN i
http://www.xiaoyu163.com
2 9
8
Mirr Time : Mirror time of between disc surface and record
surface when disc type judgment. (hexadecimal
number)
Mirr Count : The number of times which mirror counts between
disc surface and record surface when disc type
judging.
FZC Count : The number of times which focus zero cross points
of each layer when lens down.
PI Reference : The average of PI reference voltage. (hexadecimal
number)
PI Peak : PI peak level voltage. It performs only when disc
type judgment is successful. (hexadecimal number)
2-1-2. Disc Type DVD
It sets up s that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: DVD single layer disc (12 cm)
[2]
: DVD dual layers disc (0 layer, 12 cm)
[3]
: DVD dual layers disc (1 layer, 12 cm)
[4]
: DVD-RW disc (12 cm)
[5]
: DVD single layer disc (8 cm)
[6]
: DVD dual layers disc (0 layer, 8 cm)
[7]
: DVD dual layers disc (1 layer, 8 cm)
[8]
: DVD-RW disc (8 cm)
2-1-3. Disc Type CD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: CD disc (normal speed, 12 cm)
[2]
: CD disc (double speed, 12 cm)
[3]
: CD disc (normal speed, 8 cm)
Q Q
3 6 7 1 3 1 5
[4]
: CD disc (double speed, 8 cm)
[5]
: CD-RW disc (normal speed, 12 cm)
[6]
: CD-RW disc (double speed, 12 cm)
[7]
: CD-RW disc (normal speed, 8 cm)
[8]
: CD-RW disc (double speed, 8 cm)
2-1-4. Disc Type Hybrid
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: SACD Hybrid disc (SACD layer, 12 cm)
[2]
: SACD Hybrid disc (CD layer, normal speed, 12 cm)
[3]
: SACD Hybrid disc (CD layer, double speed, 12 cm)
[4]
: SACD Hybrid disc (SACD layer, 8 cm)
[5]
: SACD Hybrid disc (CD layer, normal speed, 8 cm)
[6]
: SACD Hybrid disc (CD layer, double speed, 8 cm)
2-2. Servo Control
Note: Be sure to perform the disc type setup before performing
this item.
Servo Control
1.LD off R.Sled FWD
2.Focus off L.Sled REV
3.SPDL off U.Sled Reset
4.CLVA off D.Sled Limit
5.Trk. off
6.Sled off
7.Fcs.Srch off
co
0.All Servo Off
.
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
9 4 2 8
0 5 8 2 9 9 4 2 8
m
Exit: RETURN
9 9
9 9