Honeywell ademco vista-48la Programming Manual page 19

This prompt appears if event "1" (relay on/off) was selected, otherwise it is skipped.
D E V I C E N U M B E R
Enter the physical device number as programmed in ∗79 Menu Mode, then press [*] to continue to the "Start"
X X
prompt.
Device numbers 17 and 18 designate built-in triggers 1 and 2 respectively.
01-18 = device number
[∗] to continue
This prompt appears if event "2" (user access) was selected. Otherwise it is skipped.
G R O U P N U M B E R
1-8 = group number
X
[∗] to continue to the "Start" prompt.
This prompt appears if events "3-7, or 10" were selected. Otherwise it is skipped.
P A R T I T I O N
0 = all partitions; 1 = partition 1; 2 = partition 2; 3 = partition 3
X
[∗] to continue
Enter the event's start time and days of the week to occur.
S T A R T S M T W T F S
To select days, position the cursor under the desired days using the [∗] key to move forward, then press "1"
0 0 1 0 0 0 0
H H M M A M
to select the day.
01-12 (00-23) = hour (use 00-23 if 24-hour time is enabled)
00-59 = minute
0 = AM; 1 = PM
Days = place "1" under days
[∗] to continue
This prompt appears if events "4 or 5" were selected.
W A R N I N G D L Y T I M E
Enter the desired amount of time the system should warn of impending arming. The system will beep once
0 0
every 30 seconds to alert users that arming will soon occur. Otherwise, this prompt is skipped.
01-15 = minutes of arm warning delay time
[∗] to continue
Enter the event's stop time and days of the week to occur.
S T O P S M T W T F S
To select days, position the cursor under the desired days using the [∗] key to move forward, then press "1"
0 0 1 0 0 0 0
H H M M A M
to select the day.
This entry applies only to the following events: 1 (relay on/off); 2 (user access); 3 (child-not-home report)
01-12 (00-23) = hour (use 00-23 if 24-hour time is enabled)
00-59 = minute
0 = AM; 1 = PM
Days = place "1" under days
[∗] to continue
Enter the desired repeat option for this schedule.
R E P E A T O P T I O N
e.g., To make a schedule that happens everyday you would select all days with a repeat count of 1. To make
0 - 4 X
a schedule that runs for one week then stops, select everyday with a repeat count of 0.
0 = do not repeat
1 = repeat schedule weekly
2 = repeat schedule biweekly (every other week)
3 = repeat schedule every third week
4 = repeat schedule every fourth week
[∗] to continue
If selected, the scheduled start and stop times will vary within 60 minutes of the "hour" time. For example, if a
R A N D O M I Z E
schedule is set to start at 6:15pm, it will do so the first time 6:15pm arrives, but on subsequent days it will
0 = N O 1 = Y E S X
start anytime between 6:00 and 6:59 p.m.
NOTE: Do not use the random option if the start and stop times are within the same "hour" setting, otherwise
unpredictable results may occur (e.g., the randomized stop time may occur before the start time).
0 = no
1 = yes
[∗] to continue
– 19 –