Honeywell ademco vista-48la Programming Manual page 13

✱
80 OUTPUT DEFINITIONS
NOTES: 1. For Relays, 4229, 4204, and 6164 devices are programmed in *79, *80, and *81 modes.
2. For Powerline Carrier devices (plcd), field
3. Tampers of expansion units cannot be used to operate devices.
Zone Types:
00 = Not used
01 = Entry/exit #1
02 = Entry/exit #2
03 = Perimeter
04 = Interior Follower
05 = Trouble Day/Alarm Night
06 = 24-Hr Silent
Choices for System Operation are:
20 = Arming–Stay
21 = Arming–Away
22 = Disarming (Code + OFF)
31 = End of Exit Time
32 = Start of Entry Time
33 = Any Burglary Alarm
36 = **At Siren Timeout***
OUTPUT DEFINITION WORKSHEET
Output Activation Type and Detail
Function
Activated by Zone List
Number
0=delete (ZL)
(1-48)
1=zn list 1-8 = list
2=zn type
3=zn no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
†† Duration is set in program field *177. Duration 1 (action 5) is from 15 seconds to 15 minutes. Duration 2 (action 6) is from 1 day to 7 days.
✱
07 = 24-Hr Audible 21 = Arm–AWAY*
08 = 24-Hr Aux 22 = Disarm*
09 = Fire 23 = No Alarm Resp
10 = Interior w/Delay 24 = Silent Burglary
12 = Monitor Zone 77 = Keyswitch
14 = Gas 81 = AAV Monitor Zone
16 = Fire w/Verify 82 = Blockschloss Keyswitch
20 = Arm–STAY* 90-93 = Configurable
38 = Chime 58 = Duress
39 = Any Fire Alarm 60 = AAV Trigger
40 = Bypassing 66 = Function key (use *57 Menu Mode to assign the function key, function "07,")
41 = **AC Mains Failure 67 = Siren Failure
42 = **System Battery Low 68 = Telecom Line Fault
43 = Communication Failure 78 = Keyswitch red LED (device action not used for this option)
52 = Kiss off 79 = Keyswitch green LED (device action not used for this option)
54 = Fire Zone Reset 80 = any tamper in the system
Partition
Number
Zone Type Zone No.
(P)
(ZT) (ZN)
(if using ZT trig)
(see table 00=none
0 = any
below) 01-64
1 = partition 1
2 = partition 2
3 = partition 3
27 must be programmed with a House Code.
*5800 button-type transmitters only
** Use 0 (Any) for Partition No. (P) entry.
*** Or at Disarming, whichever occurs earlier.
Event (for zone list/activated by)
By Zone List By Zone No.
0 = restore 0 = restore
1 = alarm 1 = alarm
2 = fault 2 = fault
3 = trouble 3 = trouble
4 = off-normal
– 13 –
Action Output Device
0 = off Number Type
1 = close 2
secs 1-18= dev R = relay
2 = stay closed T = trigger
3 = pulse X = X10
4 = toggle
5 = duration 1
††
6 = duration 2
††