E Model Australian Model Chinese Model HCD-LF1H is control unit (DVD player) in DAV-LF1H. This system incorporates with Dolby* Digital and Dolby Pro Logic (II) Model Name Using Similar Mechanism adaptive matrix surround decoder and the DTS** Digital Surround System.
Page 2
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
HCD-LF1H Ver. 1.1 SECTION 1 SERVICING NOTES Note about CDs/DVDs DISC SLOT LOCK The system can play CD-ROMs/CD-Rs/CD-RWs recorded in the The disc slot lock function for the antitheft of an demonstration following formats: disc in the store is equipped.
Page 5
HCD-LF1H • PRECAUTION FRONT PART The front part is easy to be scratched. Attach a protective sheet on the front part or remove the front part before the repair work. front part protective sheet • PRECAUTION DVD MECHANISM [MECH MODULE (AUR-M1)] DISASSEMBLY When removing the mech module section (AUR-M1), create a solder bridge to prevent the optical pick-up from breaking.
Page 6
HCD-LF1H • TO TAKE OUT DISC WHEN POWER SWITCH TURNS OFF (FORCE EJECT) 1. Load the disc using an external power supply. 1 Disconnect FFC 50P (160), and them remove the mech module (AUR-M1). * Please refer to SECTION 3 DISASSEMBLY (See page 11) for the method removed by the mech module (AUR-M1).
Page 7
HCD-LF1H • SERVICE POSITION (MECH MODULE (AUR-M1)) DMB14 board MAIN board FL board mech module (AUR-M1) • SERVICE POSITION (DMB14 BOARD AND MAIN BOARD) mech module (AUR-M1) MAIN board FL board DMB14 board...
HCD-LF1H SECTION 2 GENERAL This section is extracted from instruction manual. Front Panel (control unit) Top Panel A Soft-touch button indicators (42) I [/1 (on/standby) (42) B Front panel display (115) J Disc slot (42) C 1 (standby) indicator (42)
Page 9
HCD-LF1H Front Panel Display When playing back a DVD Lights up when the MOVIE or MUSIC mode is selected (page 47). Playing status Lights up when the system Lights up when the sleep outputs the progressive timer is set (page 82).
HCD-LF1H Remote control N m/M (51) (51) TUNING –/+ (75) O REPEAT (58) P VOLUME +/– (42, 76, 98) TV VOL +/– (79) Q MUTING (42) R AUDIO (59) S PICTURE NAVI (53) T PROGRESSIVE (94) U DIMMER (83) V FM MODE (76)
HCD-LF1H SECTION 3 DISASSEMBLY 3-1. DISASSEMBLY FLOW • This set can be disassembled in the order shown below. • The dotted square with arrow ( ) prompts you to move to the next job when all of the works within the dotted square ( ) are completed.
HCD-LF1H Note: Follow the disassembly procedure in the numerical order given. 3-2. COVER (REAR) ASSY, HOLDER (HDMI) PRECAUTION THE MAIN UNIT DISASSEMBLY The front part is easy to be scratched. 1 cover (screw) Attach a protective sheet on the front...
HCD-LF1H 3-9. DVD MECHANISM [MECH MODULE (AUR-M1)] SECTION-1 PRECAUTION DVD MECHANISM [MECH MODULE (AUR-M1)] DISASSEMBLY When removing the mech module (AUR-M1), create a solder bridge to prevent the optical pick-up from breaking. 6 two screws (+BVTP 3 × 6) (Use a soldering iron with an antistatic earth.) 5 screw (+BVTT 3 ×...
HCD-LF1H 3-10. DVD MECHANISM [MECH MODULE (AUR-M1)] SECTION-2 2 panel (CDM) 1 five claws 5 mech module (AUR-M1), bracket (CDM-L), etc. 3 four shafts (insulator) Do not hold the A part of mech module (AUR-M1). Doing so may deform the module.
HCD-LF1H SECTION 4 TEST MODE 3. Disc Slot Lock Note 1: Regarding the notification symbol “R” The disc slot lock function for the antitheft of an demonstration Because the number of the operating buttons of this product disc in the store is equipped.
Page 24
HCD-LF1H 8-4. MIRROR TIME ADJUSTMENT DVD SECTION 8. Mirror Time Check To enter Mirror Time Adjustment, press 5 “R” button on the remote [TEST DISC LIST] commander. The screen will appear as shown. Be sure to use the DVD disc that matches the signal standards of MIRR time Adjust Menu your region.
Page 25
HCD-LF1H Ver. 1.1 (2)Select “2. Drive Manual Operation”, by pressing the 2 “R” (12) Confirm the same values are displayed. If it is not same, button. return to step (7). MIRR time Adjust Menu Drive Manual Operation 1. CD MIRR time Check: 1.
HCD-LF1H Ver. 1.3 SECTION 5 ELECTRICAL ADJUSTMENT Checking Location: DMB14 board (Side A) DVD SECTION DMB14 BOARD (SIDE A) When the base unit is replaced, perform the adjustment and the measurement as shown below in this order. MIRROR TIME ADJUSTMENT (See page 24)
HCD-LF1H Ver. 1.2 SECTION 6 DIAGRAMS • Circuit Boards Location THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Schematic Diagrams. For Printed Wiring Boards.
HCD-LF1H Ver. 1.1 6-2. BLOCK DIAGRAM — MAIN SECTION — IC601 VIDEO AMP CR/B Y in Cr out CB/R 4 CVBS in Cb out IC511 SYSTEM CONTROL T951 CY/G COARD DC/DC CONVERTER C in CY out ROUT1- SA-WSLF1H ROUT1+ 10 CY in...
Page 53
HCD-LF1H – DMB14 Board – IC501 AK4358VQ-L AVSS AVDD VREFH LOUT1– 1 LOUT1+ 2 ROUT4+ ROUT4– DZF3 3 DATT DATT DATT DATT DATT DATT DATT DATT DZF2 4 DZF1 5 Audio DIF0 CAD0 6 ACKSN 7 PDN 8 BICK 9...
Page 54
HCD-LF1H – DMB14 Board – IC706 BR24L16F-WE2 1 A0 16 K bit EEPROM ARRAY 11 bit 8 bit 2 A1 ADDRESS SLAVE WORD DATA 11 bit DECODER ADDRESS REGISTER REGISTER START STOP 3 A2 CONTROL CIRCUIT HIGHT VOLTAGE POWER SUPPLY...
Page 55
HCD-LF1H – MAIN Board – IC601 MM1623BFBE S-DC OUT 28 VCC2 S1/S2 27 S-DC OUT 150kΩ 75Ω VCC1 BIAS 6.75MHz DRIVER LOW-PASS C IN 26 C OUT FILTER MUTE 1 25 S1 CLAMP –6dB 24 S2 CVBS IN 75Ω 6.75MHz...
Page 56
HCD-LF1H • IC Pin Function Description DMB14 BOARD IC101 CXD9804R (CD/DVD RF AMP, FOCUS/TRACKING ERROR AMP, DVD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR) Pin No. Pin Name Description AGND — Ground terminal DVDA AC coupled input path A DVDB AC coupled input path B...
Page 57
HCD-LF1H Pin No. Pin Name Description SPFG Motor hall sensor input Mute signal control output IOPMON Power monitor signal input TG EJ SW Servo 1 signal input EEWP WF signal output to EEPROM (IC103) DVDD18 — Power supply (+1.8V from IC110)
Page 58
HCD-LF1H Pin No. Pin Name Description XIFSSY DQM signal input Data bus 7 from SD-RAM (IC104) DVSS — Ground terminal 117, 118 RD 6, 5 Data bus 6, 5 from SD-RAM (IC104) DVSS — Ground terminal 120, 121 RD 4, 3...
Page 59
HCD-LF1H Pin No. Pin Name Description DVDD3 — Power supply (SW+3.3V) STBY MUTE signal output to Motor Driver (IC203) GVSW MUTE123 signal output to Motor Driver (IC203) REW signal output to Motor Driver (IC201) (not used) FWD signal output to Motor Driver (IC201) (not used)
Page 60
HCD-LF1H Pin No. Pin Name Description JITFN Negative input of operation amplifier for RF jitter meter (not used) PLLVSS — Ground terminal IDAC — Not used PLLVDD3 — Power supply (RF+3.3V) LPFON Negative output of loop filter amplifier LPFIP Positive input of loop filter amplifier...
Page 61
HCD-LF1H MAIN BOARD IC301 M30620MCP-A16FPU0 (SYSTEM CONTROLLER) Pin No. Pin Name Description FL_DOUT FL serial data output FL_CLK FL serial clock output — Not used SIRCS_IN SIRCS input 5, 6 — Not used FL_LAT FL latch signal output BYTE External data bus (Connected to ground)
Page 62
HCD-LF1H Pin No. Pin Name Description STOP_KEY STOP KEY signal input PLAY_KEY PLAY KEY signal input 54 to 61 — Not used VCC2 — Power supply (BUP+ 3.3V) — Not used — Ground terminal 65 to 73 — Not used...
HCD-LF1H Ver. 1.2 SECTION 7 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they : Mexican model The components identified by mark 9 contain may have some difference from the original : Russian model confidential information. one.
HCD-LF1H Ver. 1.2 SECTION 8 DMB14 ELECTRICAL PARTS LIST NOTE: uPB. . : µPB. . , uPC. . , µPC. . , • Due to standardization, replacements in the uPD. . : µPD. . parts list may be different from the parts •...
Page 69
HCD-LF1H Ver. 1.1 DMB14 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN601 1-774-731-21 PIN, CONNECTOR (PC BOARD) 5P IC705 6-703-046-01 IC SN74LVC1G08DCKR CN701 1-818-086-41 HDMI CONNECTOR IC706 not supplied IC BR24L16F-WE2 CN1701 1-573-806-21 PIN, CONNECTOR (1.5MM) (SMD) 6P...
Page 70
HCD-LF1H DMB14 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R153 1-216-864-11 SHORT CHIP R236 1-216-864-11 SHORT CHIP R154 1-216-864-11 SHORT CHIP R237 1-216-864-11 SHORT CHIP R155 1-216-864-11 SHORT CHIP R238 1-216-864-11 SHORT CHIP R156 1-216-809-11 METAL CHIP...
Page 71
HCD-LF1H Ver. 1.1 DMB14 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R734 1-216-864-11 SHORT CHIP R1139 1-216-864-11 SHORT CHIP R736 1-216-864-11 SHORT CHIP R1140 1-216-864-11 SHORT CHIP R738 1-216-864-11 SHORT CHIP R1141 1-216-864-11 SHORT CHIP...
Page 79
HCD-LF1H US Model Canadian Model SERVICE MANUAL AEP Model UK Model E Model Ver. 1.1 2006.09 Australian Model SUPPLEMENT-1 Subject: Addition of “EXECUTING IOP MEASUREMENT” and “EMERGENCY HISTORY” for TEST MODE This SUPPLEMENT-1 describes the “EXECUTING IOP MEASUREMENT” and “EMERGENCY HISTORY” of the TEST MODE of DVD SECTION.
Page 80
HCD-LF1H TEST MODE 8-4-2. EXECUTING IOP MEASUREMENT (5) Wait until a hexadecimal number appear. Manual Adjust In order to execute IOP measurement, the following standard procedures must be followed. 1. Track Balance Adjust: 2. Track Gain Adjust: , A and VOLUME + (1) In power on, press three buttons 3.
Page 81
HCD-LF1H 8-5-2. Clear the Emergency History • Error Code Press TOP MENU “R” button and then press CLEAR “R” button. The error code for all emergency history would be reset. Emg.History Check Laser Hours 9999h 59min Emg.History Check 9999h 59min...
HCD-LF1H REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2006.07...