Maintenance - Black & Decker 9036 Instruction Manual

FEATURES (Fig. A and B)
1. ON/OFF switch with Forward/Reverse function
2. Handle
3. Bit Holder
4. Charger Connector
5. Charge Indicator
6. Wall Charger
7. Screwdriver Bit
CHARGING THE SCREWDRIVER (Fig. B)
Before attempting to charge your screwdriver, thoroughly
read all of the safety instructions.
To charge your screwdriver, follow the steps below.
1. Plug the output cord of the charger (6) into the socket
in the back half of the screwdriver handle (4) as shown
in Fig. B.
2. Plug the charger into any standard electrical outlet.
3. The red charge indicator light next to the socket in the
back half of the handle (5) will come ON indicating that
the battery is charging. This light will remain on as long
as the the screwdriver is connected to the charger.
Charging Notes
The tool was sent from the factory in an uncharged condition.
Before attempting to use it, it must be charged for 12 hours.
1. Charger will work best at normal room temperature.
2. The charger plug and the tool handle may become
warm while charging. This is normal and does not
indicate a problem.
3. The tool can be left on charge as long as you desire.
A minimum charge time of 8 hours is required to
recharge a completely discharged tool.
4. For most fix up jobs a charge of 3 to 4 hours adequate.
5. For long periods that the screwdriver will not be used,
it is recommended that it be fully charged, disconnected
from the charger and stored in a cool, dry location.
Warning! When disconnecting the screwdriver from the
charger, be sure to unplug the charger from the outlet first
then disconnect the charger cord from the screwdriver.
USE
Removing and Installing Bits (Fig. C)
To install a screwdriver bit (6) Fig. C simply insert it into
the cavity in the bit holder (3) until it snaps into place. To
remove the bit pull it straight out. If bit does not fit, rotate
the bit and reinsert it.
Adjusting the Handle
For optimum versatility, the handle can be be set to different
positions as shown in Fig. D. To adjust the handle into the
desired position.
Note: To avoid being pinched, grasp the handle below the
pinch point shown in Fig. D.
OPERATION (Fig. E)
Forward
► Press the button on the top (Clockwise Arrow) (8)
and the tool will run forwards.
► Release the button and the tool will stop.
Reverse
► Press the button on the bottom (Counter Clockwise
Arrow) (9) and the tool will run in reverse.
► Release the button and the tool will stop.
Operating in Manual Mode
► The tool can be used as a conventional non-powered
screwdriver whenever the forward/reverse button is not
depressed. With the button (ON/OFF)(1) in the middle
position, the tool will not activate.
HINTS FOR OPTIMUM USE
► Always use the correct type of screwdriver bit.
► If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
► Use the screwdriver manually as a non powered
screwdriver to loosen very tight screws or to firmly
tighten screws.
► Always hold the tool and screwdriver bit in a straight
line with the screw.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never
let any liquid get inside the tool; never immerse any part of
the tool into a liquid.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service organizations,
always using identical replacement parts.
Your tool has been designed to operate over a long period
of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
► Clean the housing with a clean, damp cloth.
Do not use solvents.
LUBRICATION
Black & Decker tools are properly lubricated at the factory
and are ready for use.
BATTERY PACK REMOVAL
Important! This tool is designed for disassembly for the
purpose of battery pack removal and recycling. It is not
designed to be re-assembled by the consumer. Before
attempting to disassemble this tool, turn it on and run it in
either direction until it stops to ensure a complete discharge
ENGLISH • 13