Sanyo DC-X801 Instruction Manual page 11

4. Press the track number button 5 on the remote control-
ler.
"5 (flashes)" EDIT, PROG., SIDE A
5. Press the MEMO button.
"5" EDIT, PROG., SIDE A
6. Press the button 2.
"2 (flashes)" EDIT, PROG., SIDE A
7. Press the MEMO button.
"2"
EDIT, PROG., SIDE A
8. Press the button 3.
"3 (flashes)" EDIT, PROG., SIDE A
9. Press the MEMO button.
"3"
EDIT, PROG., SIDE A
10. Press the button 1.
"1 (flashes)" EDIT, PROG., SIDE A (flashes)
- This exceeds the remaining time on side A and so
the SIDE A indicator flashes.
11. Press the MEMO button.
"1" EDIT, PROG., SIDE B
- This and subsequent tracks are recorded on side B.
12. Press the button 4.
13. Press the MEMO button.
14. Press the button 8.
15. Press the MEMO button.
"8"
EDIT, PROG., SIDE B
This completes the programming.
- If a track no. that is over the remaining time is
selected, the SIDE A or SIDE B indicator will flash.
16. Press the PLAY/PAUSE switch. Recording of side A is
started automatically. The CD player will start play after
8 seconds waiting.
17. Follow steps "3" to "5" of "Time edit recording" sec-
tion.
- The tracks can also be selected using the skip/search
button on the remote controller or skip/search switch on
the main unit.
It is impossible to check, to change and to add program-
mes.
MANUAL ECORD1NG
1. Press the CD FUNCTION switch.
2. Press the REC button of the cassette deck. The deck is
ready for recording.
3. Press the PLAY/PAUSE switch of the CD player.
With normal play, play will start from track 1; with pro-
grammed play, it will start from the first programmed
track.
Note:
In this method recording will be interrupted at the end of
tape.
DUBBING OPERATION
The recording of radio programm gramophone
records or dubbing of music tapes
'missible only
insofar as copyright or other righ', jird parties are
not thereby infringed.
- This unit enables you to dub a
Drded
tape onto
another tape by using the built-in d-- 4e deck mecha-
nisms. It is performed only one w7; i TAPE A (play-
back) to TAPE B (recording).
- During dubbing operation, the DOLBY NR switch has no
effect to the copied tape.
Dubbing
1. Insert a recorded cassette into TAPE A and a blank
cassette into TAPE B.
2. Press the TAPE FUNCTION switch.
3. Set the TAPE B tape select (TAPE B SEL.) switch for the
type of tape being used.
4. Set the REVERSE MODE lever to ) or
as
desired.
5. Wind the tape on TAPE A to the be,„ ming of the tape or
a particular selection.
6. Select the dubbing speed with the JUB. SPEED/BEAT
CANCEL switch.
HIGH:
For dubbing the whole tape at high speed (twice
normal speed).
NORMAL:
For dubbing with monitoring at normal speed.
7. Press TAPE B PAUSE button and then press TAPE B
REC button.
8. Press TAPE A PLAY button. TAPE B PAUSE button will
be released and dubbing will start automatically.
9. To stop the dubbing operation, press both STOP/EJECT
buttons simultaneously.
To dub other selections repeat steps 5 to 9 as described
above.
Automatic stop in dubbing operation
a) When TAPE A tape is longer than TAPE B:
After the automatic stop has been activated on TAPE B,
TAPE A will continue to play back at normal speed.
b) When TAPE B tape is longer than TAPE A:
After the automatic stop has been activated on TAPE A,
TAPE B will not stop. The STOP/EJECT button should
then be pressed.
Note:
Do not change the dubbing speed during the dubbing
operation.
-10-