For Your Safety - Fein ASCT5-40 Manual

OBJ_BUCH-0000000006-001.book Page 16 Wednesday, June 23, 2010 8:08 AM
en
16
Character Unit of measure,
international
U
V
n /min
0
n /min
1
M... Nm
L dB
wA
L dB
pA
L dB
pCpeak
K...
2
a
m/s
2
a
m/s
h
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s

For your safety.

Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
hand-guided screwdriver for screwing in and unscrewing
screws, especially for drywall screws, in weather-pro-
tected environments using the application tools and
accessories recommended by FEIN.
Special safety instructions.
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Beware of any concealed electric cables, gas or water
conduits; check the working area with a metal detector,
for example, before commencing work.
Secure the workpiece firmly. A work piece that is gripped
tightly in a clamping device or vice, is more secure than if
held by hand.
Hold the power tool firmly. High reaction torque can
briefly occur.
Do not machine any material containing asbestos. Asbes-
tos is cancerogenic.
Unit of measure,
national
V
rpm
rpm
Nm
dB
dB
dB
2
m/s
2
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2 2
min, m/s
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection
against an electric shock will be ineffective. Adhesive
labels are recommended.
Do not use accessories which are not specifically
designed and recommended by the power tool manufac-
turer. Safe operation is not ensured merely because an
accessory fits your power tool.
Use and handling of the battery (battery pack)
To avoid hazardous situations such as burns, fire, explo-
sion, skin injuries, and other injuries when handling the
battery, observe the following instructions:
Batteries must not be disassembled, opened or reduced
in size. Do not subject batteries to mechanical impact or
shock. Hazardous vapours and fluid can escape in case of
damage and improper use of the battery. The vapours can
irritate the respiratory system. Liquid ejected from the
battery may cause skin irritations or burns.
When battery fluid from a damaged battery has come into
contact with objects close by, check the respective com-
ponents, clean them or replace them as required.
Keep the battery away from heat and fire. Do not store the
battery in direct sunlight.
Do not remove the battery from its original packaging
until it is going to be used.
Before any work on the machine itself, remove the bat-
tery from the power tool. If the power tool accidentally
starts, there is danger of injury.
Remove the battery only when the power tool is switched
off.
Keep the battery away from children.
Keep the battery clean and protect it against moisture
and water. Clean contaminated battery terminals and
power tool connections with a dry, clean cloth.
Explanation
DC voltage
No-load speed
Speed, full load
Torque (hard/soft screwdriving application)
Sound power level
Sound pressure level
Peak sound pressure level
Uncertainty
Vibrational emission value according to EN 60745
(vector sum of three directions)
Vibrational emission value (screwdriving)
Basic and derived units of measure from the inter-
national system of units SI.