1. Manuals
  2. Brands
  3. NEC Manuals
  4. Monitor
  5. MultiSync FP1375X
  6. User manual

NEC MultiSync FP1375X User Manual

Nec display solutions colour monitor user's manual fp1375x
Hide thumbs Also See for MultiSync FP1375X:
Table of Contents

Advertisement

Quick Links

See also: User Manual
MultiSync FP1375X
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for NEC MultiSync FP1375X

Summary of Contents for NEC MultiSync FP1375X

  • Page 1 MultiSync FP1375X User’s Manual...
  • Page 2 Declaration Declaration of the Manufacturer We hereby certify that the colour monitor MultiSync FP1375X (NSZ3101STTUW) is in compliance with Council Directive 73/23/EEC: Council Directive 89/336/EEC: and marked with NEC-Mitsubishi Electric Visual Systems Corporation - EN 60950 - EN 55022 - EN 61000-3-2...

  • Page 3: Safety Instruction

    U.S. registered trademark. All other brands and product names are trademarks or NERGY registered trademarks of their respective owners. As an E Partner, NEC-Mitsubishi Electric Visual Systems Corporation has determined that NERGY this product meets the E NERGY The E emblem does not represent EPA endorsement of any product or service.

  • Page 4: Canadian Department Of Communications Compliance Statement

    C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 #950. FCC Information Use the attached specified cables with the MultiSync FP1375X colour monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cable or equivalent to ensure FCC compliance.

  • Page 5: Table Of Contents

    Contents Your new MultiSync FP1375X monitor box* should contain the following: • MultiSync FP1375X Monitor with tilt/swivel base • Power cord for E.U. • Power cord for U.K. • Video Signal Cable (VGA to DVI-A) • Video Signal Cable (DVI-D to DVI-D) •...

  • Page 6: Usb Cable

    Quick Start To attach the MultiSync FP1375X monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. If necessary, install the display card into your system. For more information, refer to the display card manual.

  • Page 7: Vga To Dvi-A

    95/98/2000/Me INF file for your MultiSync monitor can be found on the CD-ROM, delivered with the monitor. 5. Connect one end of the power cord to the MultiSync FP1375X monitor and the other end to the power outlet (Figure C.1).

  • Page 8: Brightness/Contrast Controls

    Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: Main Menu EXIT Exits the OSM menu. CONTROL L/M Moves the highlighted area up/down to select one of the controls. CONTROL -/+ Moves highlighted area left/right to select one of the controls.

  • Page 9: Size And Position Controls

    Degauss: Eliminates the build-up of stray magnetic fields which alter the correct scan of the electron beams and affect the purity of the screen colours, focus, and convergence. When activated, your screen image will jump and waver a bit as the screen is demagnetised. Caution: Please allow a minimum of 20 minutes to elapse between uses of the Degauss function.
  • Page 10 Sides Left/Right (pincushion balance): Decreases or increases the curvature of the sides either to the left or right. Sides Tilt (parallelogram): Decreases or increases the tilt of the sides either to the left or right. Sides Align (trapezoidal): Decreases or increases the bottom of the screen to be the same as the top.
  • Page 11 LEFT, TOP RIGHT, BOTTOM LEFT or BOTTOM RIGHT), use the –/+ control buttons to fine tune the GlobalSync corrections. Note: NEC recommends that you perform GlobalSync correction while running a typical application such as a spreadsheet or text document. Auto Save: The monitor automatically saves the last settings of the user controls.
  • Page 12 NOTE: For standard systems and graphics boards, keep the factory setting at ENABLE. EdgeLock Control: Operating your monitor at a non-standard timing may cause images to appear darker than normal or have colour distortion. Use of the EdgeLock control will adjust images to their normal state.

  • Page 13: Recommended Use

    • When operating the MultiSync FP1375X with its AC 220-240V worldwide power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used. The power supply cord you use must have been approved by and comply with the safety standards of your country.
  • Page 14 • Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated openings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor. • The power cable connector is the primary means of detaching the CAUTION system from the power supply.

  • Page 15: Specifications

    (Factory setting) Active Display Area (Full scan) USB connection Power Supply Current Rating Monitor + USB Hub: Dimensions Weight MultiSync FP1375X Diagonal: 55 cm/22 inch 508 mm/20 inch Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync.
  • Page 16 Operating Temperature: Humidity: Storage Temperature: Humidity: NOTE: Technical specifications are subject to change without notice. MultiSync FP1375X +10 °C to +35 °C 30% to 80% 0 to 3,000 m Altitude: -20 °C to +60 °C 10% to 90% 0 to 13,700 m...
  • Page 17 Features Flat Aperture Grille CRT: Delivers an unparalleled viewing experience with a virtually flat image, eliminating distortion and reducing glare so that what you see on-screen is what you get on your printed output. The striped phosphor alignment of the CRT delivers superior vertical definition with improved bright-ness for more uniform image contrast.
  • Page 18 FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size. GlobalSync /Corner Purity Control: NEC ’s unique design automatically eliminates picture impurities that may result from stray magnetic fields (including the earth ’s permanent magnets,etc.) and now allows you to easily adjust impurities in the four corners of your monitor.

  • Page 19: Monitor Troubleshooting

    Monitor Troubleshooting No picture • Display card should be completely seated in its slot. • Power Button and computer power switch should be in the ON position. • Signal cable should be completely connected to display card/ computer. • Check connector for bent or pushed-in pins. Image is scrolling or unstable •...
  • Page 20 Display image is not centered, too small, or too large • Use the OSM Size and Position Controls to adjust the image. Thin horizontal lines appear on your screen • Thin horizontal lines are normal for an aperture grille CRT and are not a malfunction.
  • Page 21 TCO’99 Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
  • Page 22 The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical and magnetic fields, energy consumption and electrical and fire safety. The environmental demands concern restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things.
  • Page 23 Cadmium** Cadmium is present in rechargeable batteries and in the colourgenerating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. TCO’ 99 requirement states that batteries, the colourgenerating layers of display screens and the electrical or electronics components must not contain any cadmium.

This manual is also suitable for:

Nsz3101sttuw

Table of Contents