Assembling Instructions; Care And Cleaning - Osterizer 250-22 Instruction Manual

ASSEMBLING INSTRUCTIONS

ASSEmbLINg THE JAR
CAUTION: Follow these important steps to assemble, tighten, and mount blender jar
quickly and correctly. INJURY MAY RESULT IF MOVING BLADES ARE EXPOSED.
1.
1. Turn jar upside down so the small opening
is at the top.
2. Place sealing ring on jar opening.
TIgHTENINg THE JAR
b
A
L
eft
R
ight
S
top S
top
J
aR
L
ug
M
otoR
B
aSe
C D
2. 3.
3. Turn the blade blades upside down
and place in mouth of jar.
4. Thread jar bottom to jar.
A. To tighten jar bottom, put assembled jar
securely into motor base ring with handle
and lug in front of the right stop.
b. Using jar handle, turn jar to the left as
far as possible. This insures that the jar
bottom is tightened properly. Remove jar
from motor base and mount.
C. To operate Blender, place assembled jar
in motor base ring with jar lug against
flat side of the motor base stop. If jar lug
does not rest against flat side of right stop,
remove jar assembly and place against
flat side of left stop. Seat jar firmly and
operate.
D. To remove jar, lift straight up. (If it is not
easily removed, rock gently and lift up, do
not twist). If jar bottom cannot be loosened
by hand, place assembled jar into motor
base ring with handle in front of left side
stop. Using handle, turn jar to right until jar
bottom loosens.
Do not attempt to place the jar on or
attempt to remove it from the motor base
while the motor is running.
E n g l i s h -5
OPERATING INSTRUCTIONS
Your blender operates with multiple speeds (for models with a rotary switch) or one speed (for
models with a toggle switch).
1. FOR CONTINUOUS blending, select one of the speeds (for models with a rotary switch) or
move the toggle switch up to the "I" position (for models with a toggle switch).
2. CONTROLLED CYCLE is used for chopping pieces of food, such as vegetables, nuts or
4.
cheeses.
For models with a rotary switch:
a. For Low Controlled Cycle, turn the rotary button intermittently between the off "O"
position on the left and the low speed position.
b. For High Controlled Cycle, turn the rotary button intermittently between the off "O"
position on the right and the high speed position.
For models with a toggle switch:
For Controlled Cycle, toggle intermittently by pushing down to the pulse "
When on, the food is chopped and tossed away from the blades. When off, the food is
distributed around the blades to make processing more uniform.
NOTE: A cycle consists of operating the blender for about two seconds and then allowing
the blades to coast to a stop.
Blender jar parts are corrosion resistant, sanitary and easily cleaned. Before first use and after
every use, separate jar parts and clean thoroughly in warm, soapy water, then rinse and dry
well. DO NOT WASH ANY PARTS IN AN AUTOmATIC DISHWASHER.
Periodically check all parts before re‑assembly. If the processing blades are stuck or
difficult to turn, DO NOT USE bLENDER. Check by carefully turning the blades in a
counterclockwise direction (opposite edges are sharp). Blades should turn freely.
If the jar is chipped or cracked, DO NOT USE BLENDER. Further use could result in the
jar breaking during use. Use only replacement parts recommended by the manufacturer
available at an Authorized Service Center.
USE OF DAmAgED OR NON-RECOmmENDED PARTS COULD RESULT IN SEVERE
PERSONAL INJURY AND/OR DAmAgE TO THE bLENDER. See the "Assembling the
Jar" and "Tightening the Jar" sections for proper jar assembly and user instructions.
NEVER ImmERSE THE mOTOR bASE IN WATER. The housing can be cleaned with a
damp cloth (unplug first). The motor is permanently lubricated and does not require any
additional lubrication. ANY SERVICINg SHOULD bE PERFORmED bY AN
AUTHORIZED SERVICE FACILITY.

CARE AND CLEANING

En g lis h -6
" position.