Timer Operation - Fujitsu AGYG14LVCB Operating Manual

TIMER OPERATION

Before using the timer function, be sure that the Remote Controller is set to the correct current time (☞ P. 4).
To Use the ON timer or OFF timer
1
Press the START/STOP button (Fig. 5 O)
(If the unit is already operating, proceed to step 2).
The indoor unit's OPERATION Indicator Lamp (green) (Fig. 3 6 ) will light.
2
Press the TIMER MODE button (Fig. 5 M) to select the
OFF timer or ON timer operation.
Each time the button is pressed the timer function changes in the following
order:
PROGRAM (OFF → ON, OFF ← ON)
The indoor unit's green TIMER Indicator Lamp (orange) (Fig. 3 7) will light.
3
Use the TIMER SET buttons (Fig. 5 S) to adjust the
desired OFF time or ON time.
Set the time while the time display is fl ashing (the fl ashing will continue for
about 5 seconds).
button: Press to advance the time.
button: Press to reverse the time.
About 5 seconds later, the entire display will reappear.
To Use the Program timer
1
Press the START/STOP button (Fig. 5 O).
(If the unit is already operating, proceed to step 2).
The indoor unit's OPERATION Indicator Lamp (green) (Fig. 3 6) will light.
2
Set the desired times for OFF timer and ON timer.
See the section "To Use the ON timer or OFF timer" to set the desired mode
and times.
About 3 seconds later, the entire display will reappear.
The indoor unit's TIMER Indicator Lamp (orange) (Fig. 3 7) will light.
3
Press the TIMER MODE button (Fig. 5 M) to select the
PROGRAM timer operation (OFF
will display).
The display will alternately show "OFF timer" and "ON timer", then change to
show the time setting for the operation to occur fi rst.
● The program timer will begin operation. (If the ON timer has been selected
to operate fi rst, the unit will stop operating at this point.)
About 5 seconds later, the entire display will reappear.
About the Program timer
The program timer allows you to integrate OFF timer and ON timer operations in a
●
single sequence. The sequence can involve 1 transition from OFF timer to ON timer,
or from ON timer to OFF timer, within a 24 hour period.
The fi rst timer function to operate will be the 1 set nearest to the current time. The
●
order of operation is indicated by the arrow in the Remote controller's Display (OFF
→ ON, or OFF ← ON).
● One example of Program timer use might be to have the air conditioner automati-
cally stop (OFF timer) after you go to sleep, then start (ON timer) automatically in the
morning before you arise.
CANCEL OFF ON
ON or OFF ON
To Cancel the Timer
Use the TIMER button to select "CANCEL".
The air conditioner will return to normal opera-
tion.
To Change the Timer Settings
Perform steps 2 and 3.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
SUPER QUIET mode), after making the timer
setting wait until the entire display reappears,
then press the appropriate buttons to change
the operating condition desired.
To Cancel the Timer
Use the TIMER MODE button to select "CAN-
CEL".
The air conditioner will return to normal opera-
tion.
To Change the Timer Settings
1. Follow the instructions given in the section "To
Use the ON Timer or OFF Timer" to select
the timer setting you wish to change.
2. Press the TIMER MODE button to select
either OFF ON or OFF
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions (Mode,
Fan Speed, Thermostat Setting, SUPER QUIET
mode), after making the timer setting wait until
the entire display reappears, then press the
appropriate buttons to change the operating
condition desired.
ON.
En-9