Shark Explore-R Manual
  1. Manuals
  2. Brands
  3. Shark Manuals
  4. Motorcycle Accessories
  5. Explore-R
  6. Manual

Shark Explore-R Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SHARK Explore-R

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Explore-R and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Shark Explore-R

Summary of Contents for Shark Explore-R

  • Page 1 SHARK Explore-R...

  • Page 2: Table Of Contents

    • Easy Fit ................. 16 • 5 year guarantee ..............17 • Legally required information ..........18 The shell of your helmet Explore-R is made The intrinsic structure of this material allows a good distribution of force during an impact.

  • Page 3: Anatomy Of The Helmet

    ANATOmy Of ThE hElmET 1) Visor 2) Sun shield 7 - “Precise lock“ chinstrap buckle 3) Goggles 4) Sun shield mechanism 5) Upper ventilation 6) Rear venturi 7) Chin strap buckle (version according to countrie) 8) Base seal 9) Visor seal 7 - Double-D ring chinstrap buckle...

  • Page 4: A Helmet In Your Size

    Once you have taken this measurement, compare it it is too big or else the chin strap is not correctly to the table of sizes. Try the size of Explore-R helmet tightened. Keep trying on helmets until you find the closest to the measurement obtained, starting with ideal size.

  • Page 5: Advice For Use

    ADVICE fOR uSE accordance with the recommendations 1/ Putting on the helmet that are appropriate to the versions Once the chin strap is released, you have to take hold of the two sections by the and country. buckles and hold them slightly apart to Check that the tension and therefore the facilitate the passage of your head.

  • Page 6: The Chin Strap

    Warning: never ride with the chin strap loose or adjusting buckle (Figs. A, B, C and D). Choose insufficiently tightened. Even though the interior your Explore-R helmet and attach the holding padding gives you the impression of being held, system. When the “Precise Lock” is adjusted your helmet risks coming off in a fall.

  • Page 7: The Chin Strap

    ChIN STRAP - DOublE-D RING buCklE 1. Slide the longest part of the strap through WARNING: Ne ve r use t he stra p lo op both rings, while checking that the comfort t o secure yo ur helme t to your hea d. padding is positioned between the strap and In orde r to be properly f astened, you must your neck.

  • Page 8: The Visor

    ADJuSTmENT Of AJAR Release this lock by opening the visor (D). The SHARK EXPLORE–R is equipped with In ajar position, it is not possible to close a command which enable to open your visor the visor. It is necessary to lift it up to unlock with a simple gesture, and to lock it by letting passed an ajar (C).

  • Page 9: The Sun Shield

    SuN VISOR The EXPLORE-R SHARK is equipped with To ensure its protection and lengthen its li- fespan, the external surface of the EXPLORE-R an Integral sun shield with external controls. sun shield has been coated with an an- Warning: this sun shield can be used only in ti-scratch treatment.

  • Page 10: Auto Seal / Peak

    Your helmet VISION–R has a patented system SHARK “AUTOSEAL”. This system ensures visor when it is in lower position. ADJuSTING ThE PEAk Adjust the peak to required position (C).

  • Page 11: Goggles

    GOGGlES When cleaning the screen, use warm water The SHARK Explore-R helmet can be used (less than 40 degrees) and microfiber delivered with SHARK goggles reference VZ 7400 certified with goggles to wipe the screen. Neutral soap according to the European standard EN 1938: 2010.

  • Page 12: Ventilations

    VENTIlATIONS VENTIlATION INSIDE ThE hElmET uPPER VENTIlATIONS The upper ventilations provides an organised air flow set in open (A) or closed (B) position by sliding the over the surface of the head. These top air inlet are cursor from side to side for both airvents. lOWER VENTIlATION lOWER VENTIlATION To open (C) or close (D) the lower ventilation, push the...

  • Page 13: Textile Parts

    The textile and foam parts providing comfort nance, the length of use and also the degree to the Explore-R make it easy for you to ap- of acidity of your perspiration. If you note any preciate the performance of your helmet to wear, we advise you to replace the interior the full.
  • Page 14 TExTIlE PARTS - REmOVAl ChEEk PADS cheek pads from their holding by unclip- Verify that the 2 sides of the chin strap are not attached. Dismount the ping the snaps. Remove the cheek pads. CAP lINING Unclip the rear of the removable cap lining housing by gently pulling backward (C).You can (A-B).
  • Page 15 TExTIlE PARTS - REPlACE CAP AND ChEEkS Replace the cheeks pads by clipping it (G). Perform the operation in reverse. Insert IMPORTANT: Check that the chin straps aren’t the front plastic part in its housing. The 3 clips twisted or wedged under the cheeks pad. must be properly engaged (E).

  • Page 16: Cleaning

    It is essential to dry textile using the helmet. ANTI-fOG mASk ChIN COVER EASy fIT Your EXPLORE-R is equipped with The small chin cover of your Your helmet EXPLORE-R has been EXPLORE-R solidary with designed to provide additional a removable anti-fog mask.

  • Page 17: Year Guarantee

    5) ageing due to normal wear of the inner fabrics or foams, If SHARK is unable to carry out the repair for technical reasons the appearance of the external parts, or the visor (scratches, or because a component is not available, SHARK undertakes marks, etc.)

  • Page 18: Legally Required Information

    Caution: Do not apply any paint, stickers, petrol or any other solvent to this helmet. Only the visors SHARK VZ120 appro- ved under No. 050 153 and the goggles approved under No VZ 7400 NF EN 1938 2010 must be used with this helmet.

Table of Contents