Hitachi DH 40FR Technical Data And Service Manual page 29

PARTS
ITEM
CODE NO.
NO.
100 NAME PLATE
* 101 980-063 TERMINAL
* 101 930-804 TERMINAL M4.0 (10 PCS.)
102 940-778 CORD ARMOR D10.7
* 103 960-266 CORD CLIP
* 103 981-987Z CORD CLIP
104 984-750 TAPPING SCREW (W/FLANGE) D4X16
* 105 500-390Z CORD
* 105 500-434Z CORD
* 105 500-391Z CORD
106 938-307 PILLAR TERMINAL
STANDARD ACCESSORIES
ITEM
CODE NO.
NO.
501 322-152 CASE (PLASTIC)
502 981-840
GREASE (A) FOR HAMMER.HAMMER DRILL (30G)
503 943-277 HEX. BAR WRENCH 3MM
504 944-458 HEX. BAR WRENCH 4MM
505 944-459 HEX. BAR WRENCH 5MM
506 993-245 DUST COVER
OPTIONAL ACCESSORIES
ITEM
CODE NO.
NO.
601 985-374 DRILL BIT D13X400L (D1/2"X16")
602 985-375 DRILL BIT D25X400L (D1"X16")
603 985-376 DRILL BIT D38X400L (D1-1/2"X16")
604 985-377 A-TAPER SHANK ADAPTER
605 985-378 B-TAPER SHANK ADAPTER
606 944-477 COTTER
607 984-029 CORE BIT SHANK D35 (1-3/8") OR BELOW
608 985-379 CORE BIT SHANK D38 (1-1/2") OR ABOVE
609 985-380 CORE BIT 50MM
610 985-388 GUIDE PLATE (FOR CORE BIT 50MM)
611 955-159 CORE BIT 105MM
612 955-169 GUIDE PLATE (FOR CORE BIT 105MM)
613 955-165
CENTER PIN (A) 133L FOR CORE BIT D38-150
614 985-383 BULL POINT 300MM (12")
615 985-381 COLD CHISEL W25X300L (1"X12")
616 985-382 COLD CHISEL W25X460L (1"X18")
617 985-384 CUTTER W38X300L (1-1/2"X12")
618 985-385 CUTTER W50X300L (2"X12")
619 985-386 SCOOP 105X405L (4-1/2"X16")
620 320-859 SYRINGE (BLOW-OUT BULB TYPE)
621 318-085 SYRINGE (BELLOWS TYPE)
622 308-471
GREASE FOR HAMMER.HAMMER DRILL (70G)
623 980-927
GREASE FOR HAMMER.HAMMER DRILL (500G)
- -- 4 - --
DESCRIPTION
DESCRIPTION
DESCRIPTION
* ALTERNATIVE PARTS
NO.
REMARKS
USED
1
1
1 FOR USA, CAN
1
1
1 FOR SUI
2
1 (CORD ARMOR D10.7)
1 (CORD ARMOR D10.7) FOR USA, CAN
1 (CORD ARMOR D10.7) FOR SUI
1
NO.
REMARKS
USED
1
1
1
1
1
1
NO.
REMARKS
USED
1
1
1
1
1
1
1
1
1 INCLUD. 610
1
1 INCLUD. 612
1
1
1
1
1
1
1
1
1
1
1
1
DH 40FR
Printed in Japan
7 -- 03
(030715N)