Spark Arrestor - Homelite F-3055 User Manual

F3055_25 lgs.qxp 5/04/06
GB
F D E I
MAINTENANCE
Push down and turn the spool anticlockwise until it no
■
longer turns. Hold the spool down and rotate
clockwise a small amount. Release the spool.
The spool should be locked down in the string head.
If not, hold down and rotate until locked.
Make sure the string head and the spool retainer are
■
installed on the shaft connector (38) by turning the
retainer anti-clockwise to tighten.
Pull the strings again to rotate the spool into cutting
■
position. Push the spool retainer down while pulling
on string(s) to manually advance the string and to
check for proper assembly of the string head.
STRING REPLACEMENT (Fig. 18 - 21)
Stop the engine and disconnect the sparking plug
■
wire. Hold the string head and unscrew the spool
retainer. Turn clockwise.
Remove the spool from the string head.
■
NOTE: Keep the spring attached to the spool.
Remove any old string remaining on the spool.
Cut two pieces of string, each being approximately
■
2.7 m long.
Insert the first string (55) into the anchor hole (56) in
■
the upper part of the spool. Wind the first string round
the upper part of the spool anticlockwise, as shown
by the arrows on the spool (57). Place string in the
slot on upper spool flange, leaving about 152 mm
extended beyond the slot. Do not overfill.
After winding the string, there should be at least
6 mm between the wound string and the outside edge
of the spool.
Repeat above step with second string (58), using the
■
bottom part of spool. Do not overfill.
Replace the spool and the spool retainer. Refer to
■
"Spool Replacement" earlier in this manual.
BLADE PROTECTOR (Fig. 22)
Always place the blade protector (59) on the blade when the
unit is not in use. The blade protector has clips (60) round
the edges to snap over the blade and keep it in place.
Wear gloves and be cautious when handling the blade.
NOTE: Always remove the blade protector before using
the unit. If not removed, the blade protector could
become a thrown object as the blade begins to turn.
17:38 Page 22
P NL S DK N FIN GR HU
English
CZ RU RO PL SLO HR TR EST LT
CLEANING THE EXHAUST PORT AND MUFFLER
Depending on the type of fuel used, the type and amount
of oil used, and/or your operating conditions, the exhaust
port and muffler may become blocked with carbon
deposits. If you notice a power loss with your petrol-
powered tool, a qualified service technician will need to
remove these deposits to restore performance.

SPARK ARRESTOR

The spark arrestor must be cleaned or replaced every
25 hours or yearly to ensure proper performance of
your product. Spark arrestors may be in different locations
depending on the model purchased. Please contact your
nearest service dealer for the location of the spark
arrestor for your model.
Cleaning Instructions:
Remove the spark arrester from the muffler.
■
If your spark arrester is made of fibreglass, discard
■
and replace.
If your spark arrester is made of metal, follow these
■
cleaning instructions:
1. Spray the spark arrester with a quality carbon cleaner.
2. Gently clean using a wire brush.
3. Install the new or cleaned spark arrester and
reassemble completely before use.
REPLACING AND CLEANING AIR FILTER
(Fig. 23 - 24)
For proper performance and long life, keep air filter clean.
Remove the air filter cover by pushing down on the
■
latch with your thumb while gently pulling on the
cover (65).
Remove the filter, clean it in warm soapy water.
■
Rinse and let dry completely. For best performance,
replace annually.
Reinstall the filter.
■
Replace the air filter cover by inserting the tabs on
■
the bottom of the cover (64) into the slots on the air
filter base (63); push the cover up until it latches
securely in place.
22
LV SK BG