String Replacement; Cleaning Exhaust Port; Cleaning Air Filter Screen; Spark Arrestor - Homelite MIGHTYLITE 26SS Operator's Manual

 Make sure the two strings are captured in the slots op-
posite each other on the new spool. Make sure the end
of each string is extended approximately 6 in. beyond
each slot.
 Align the slot(s) on the spool to the eyelet(s) on the string
head housing. Push down and turn the spool in the nec-
essary direction to align the slot(s).
 Make sure the string head and the spool retainer are
installed on the drive shaft.
To install the spool retainer:
Turn the spool retainer clockwise for MightyLite 26CS.
Turn the spool retainer counterclockwise for MightyLite
26SS.
 Slide strings into the housing eyelets and pull outward to
rotate the spool into the cutting position.
 Push the spool retainer down while pulling on string(s)
to manually advance the string and to check for proper
assembly of the string head.

STRINg REPLACEMENT

See Figures 11 - 13.
 Stop the engine and disconnect the spark plug wire. Hold
the string head and unscrew the spool retainer.
To remove the spool retainer:
Turn the spool retainer counterclockwise for MightyLite
26CS.
Turn the spool retainer clockwise for MightyLite 26SS.
 Remove the spool from the string head.
NOTE: Keep the spring attached to the spool. Remove
any old string remaining on the spool.
 Cut one piece of trimmer line 18 ft. long. Find the middle
of the string section. Loop the string around the hook in
the center of the spool. Carefully wind the string in the
direction indicated on the top of the spool. Nearing the
end of the string, slide one end of the string into each
slot of the spool. Do not overfill.
 Replace the spool and the spool retainer. Refer to Spool
Replacement earlier in this manual.
CLEANINg ThE EXhAUST PORT
Depending on the type of fuel used, the type and amount
of lubricant used, and/or your operating conditions, the
exhaust port may become blocked with carbon deposits.
If you notice a power loss with your gas powered tool, you
may need to remove these deposits to restore performance.
We highly recommend that only qualified service technicians
perform this service.

SPARK ARRESTOR

The spark arrestor must be replaced every 50 hours or yearly
to ensure proper performance of the product. Spark arres-
tors may be in different locations depending on the model
purchased. Please contact the nearest service dealer for the
location of the spark arrestor for your model.
MAINTENANCE
CLEANINg ThE AIR FILTER SCREEN
See Figures 14 - 15.
For proper performance and long life, keep air filter screen
clean.
 Remove the air filter cover by pushing down on the latch
with your thumb while gently pulling on the cover.
 Brush the air filter screen lightly to clean.
 Replace the air filter cover by inserting the tabs on the
bottom of the cover into the slots on the air filter base;
push the cover up until it latches securely in place.
FUEL CAP
A leaking fuel cap is a fire hazard and must be replaced
immediately. Failure to do so may result in serious
injury.
The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine perfor-
mance. If performance improves when the fuel cap is loos-
ened, check valve may be faulty or filter clogged. Replace
fuel cap if required.
SPARK PLUg
This engine uses a Champion RCJ6Y or equivalent spark
plug with .025 in. electrode gap. Use an exact replacement
and replace annually, or more frequently if necessary.
STORINg ThE TRIMMER
 Clean all foreign material from the trimmer. Store it in a
well-ventilated place that is inaccessible to children. Keep
away from corrosive agents such as garden chemicals
and de-icing salts.
 Abide by all Federal and local regulations for the safe
storage and handling of gasoline.
WhEN STORINg 1 MONTh OR LONgER:
 Drain all fuel from tank into a container approved for
gasoline. Run engine until it stops.
Page 9 — English
WARNINg: