Miter Saw Safety Warnings - Makita LS1216 Instruction Manual

52° (left and right)
Thickness of wood
facing on guide
fence for increased
height of cut
60° (right)
Thickness of wood
facing on guide
fence for increased
height of cut
Special Max. Cutting capacities
Crown molding 45° type (with Crown molding stopper used)
Base board (H) (with Horizontal vise used)
Special Max Width Cutting Capacities (with 38 mm (1-1/2") thick platform used)
Bevel angle
0°
Refer to OPERATION for the cutting procedure.
–1
No load speed (min ) ............................................................................................................................................ 3,200
Laser Type (LS1216L, LS1216FL only) ..................................................Red Laser 650 nm, <1.6 mW (Laser Class 2M)
Dimensions (L x W x H) .....................................................................................................806 mm x 640 mm x 721 mm
Net weight
For all countries other than European countries
LS1216 .............................................................................................................................................................. 26.3 kg
LS1216L/LS1216F............................................................................................................................................. 26.4 kg
LS1216FL .......................................................................................................................................................... 26.5 kg
For European countries
LS1216 .............................................................................................................................................................. 26.5 kg
LS1216L/LS1216F............................................................................................................................................. 26.6 kg
LS1216FL .......................................................................................................................................................... 26.7 kg
Safety class ................................................................................................................................................................ /II
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for accurate straight and miter cut-
ting in wood. With appropriate saw blades, aluminum can
also be sawed.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future refer-
ence.
–
–
25 mm –
35 mm –
–
–
25 mm –
35 mm –
Miter angle
45° (Left and right)

MITER SAW SAFETY WARNINGS

1.
ENE006-1
2.
3.
4.
ENF002-2
5.
6.
7.
8.
GEA010-1
9.
10. Select saw blades in relation to the material to
11. Do not use the saw to cut other than wood, alu-
87 mm × 233 mm
102 mm × 220 mm
115 mm × 178 mm
120 mm × 155 mm
87 mm × 185 mm
102 mm × 178 mm
115 mm × 140 mm
120 mm × 122 mm
0°
Keep hands out of path of saw blade. Avoid con-
tact with any coasting blade. It can still cause
severe injury.
Check the saw blade carefully for cracks or
deformation before operation.
Replace damaged blade immediately.
Replace the kerf board when worn.
Use only saw blades specified by the manufac-
turer which conform to EN847-1.
Do not use saw blades manufactured from high
speed steel.
Wear eye protection.
Wear hearing protection to reduce the risk of
hearing loss.
Wear gloves for handling saw blade (saw blades
shall be carried in a holder wherever practicable)
and rough material.
Connect miter saws to a dust collecting device
when sawing.
be cut.
minum or similar materials.
–
–
–
–
–
–
–
–
203 mm
165 mm
Max. cutting
416 mm
292 mm
ENB034-10
17