Table of Contents
Advertisement
Monitoring
<Memo>: The following describes how to monitor
audio using headphones .
To monitor audio via speakers, use the [OUTPUT] (L
and R) connectors on the right side panel . These con-
nectors output the recorder's left and right input sig-
nals (or playback signals during playback) at the fixed
level .
Connect stereo headphones to the [PHONES]
jack on the right side panel .
HOLD
HOLD
REMOTE
POWER
POWER
OUTPUT
PHONES
You can adjust the headphone monitor level us-
ing the [VOLUME] control on the front panel .
1
2
80
80
HPF
OFF
200
OFF
200
OFF
L
M
L
M
LINE
H
LINE
H
LINE
GAIN
PK
PK
PK
0
10
0
10
PAN
L
R
L
R
L
C
C
You can also select the headphone monitor
source using the headphone monitor source se-
lector below the [VOLUME] control .
Normally, set the selector to the "S" position .
With this position, you can monitor the recorder's
left and right input signals (or playback signals
during playback) in stereo .
By setting the selector to the "L" or "R" position,
you can monitor the left or right channel signal
of the recorder's stereo signals in mono . You can
easily check the left and right recording (or re-
corded) signals individually .
By setting the selector to the "RTN" position, you
can monitor the input signal of the [RTN IN] jack
on the right side panel .
Basic.operations
USB
DC-IN
9-24V
LEFT
RIGHT
SD
RTN IN
3
REC
DC-R302
80
200
L
M
H
L
VOLUME
R
LIMITER
40 30 25 20 15 10 5
0 OL
-dB
DISP LIGHT
MIN
0
10
R
RTN
EXIT
ENTER
-/DOWN
+/UP
MENU
L S
C
HPF
LINE
GAIN
PK
PAN
Each input signal is sent to the stereo mix buss
and mixed . Then the mixed signals are sent to
the recorder as well as output from the [OUTPUT]
connectors .
Using the level control, you can adjusts the
amount of the corresponding input signal sent to
the recorder . To record audio without distortion,
set the level controls appropriately so that the
"OL" (overload) indicators do not light .
<Memo>: The limiter on the stereo bus automati-
cally works for a sudden excessive hot signal to re-
duce the level for preventing audio distortion . While
MAX
R
the limiter is working, the [LIMITER] indicator lights in
yellow .
The [PAN] switch decides the input signal's desti-
nation .
When you set the switch to "L", the signal is sent
to the left buss and recorded to the left track . In
other words, the signal is positioned to the left in
stereo .
When you set the switch to "R", the signal is sent
to the right buss and recorded to the right track .
In other words, the signal is positioned to the
right in stereo .
When you set the switch to "C", the signal is sent
to both the left and right busses equally and re-
corded to both the left and right tracks . In other
words, the signal is positioned to the center in
stereo .
Level
control
Input
signal
Input
signal
Input
signal
12
Mixer.setting
1
2
3
80
80
80
OFF
200
OFF
200
OFF
200
L
M
L
M
L
M
H
LINE
H
LINE
H
L
R
PK
PK
-dB
40 30 25 20 15 10 5
0
10
0
10
0
10
L
R
L
R
L
R
EXIT
ENTER
C
C
C
L
R
-dB
40 30 25 20 15 10 5 0 OL
PAN
Limiter
switch
L
R
L
R
L
R
REC
DC-R302
VOLUME
LIMITER
0 OL
DISP LIGHT
MIN
MAX
RTN
R
-/DOWN
+/UP
MENU
L
S
OUTPUT
LEFT
Recorder
RIGHT
Advertisement
Table of Contents
